Star Micronics Line Thermal Printer Specifications page 153

<Printer status 7 Position for Presenter Paper (Ninth Byte)>
Bit Contents
7 Fixed at "0"
6 Not Used (Fixed at "0")
5 Not Used (Fixed at "0")
4 Fixed at "0"
3 Presenter Paper Position
2 Presenter Paper Position
1 Presenter Paper Position
0 Fixed at "0"
• This status is valid only on models provided with a presenter. Models not provided with a presenter should send this
status fixed at "0."
• This status is made valid and invalid using the memory switch only on models provided with a presenter.
When valid, the presenter paper position status is updated, but when invalid, the presenter paper position status is fixed
at "0" and there is no change in status.
• Details of the Presenter Paper Position
bit bit bit Presenter Paper Position
3 2 1
0 0 0 Paper position 0 State where there is no paper in presenter
0 0 1 Paper position 1 State where paper is supplied (loop state)
0 1 0 Paper position 2 (Reserved)
0 1 1 Paper position 3 State where paper is discharged (Can be pulled out)
1 0 0 Paper position 4 (Reserved)
1 0 1 Paper position 5 (Reserved)
1 1 0 Paper position 6 State where paper is recovered
1 1 1 Paper position 7 State where paper is pulled out.
• Presenter operation mode: Paper position status transition
Operating Paper
Mode
Loop Recovery
Take-up
Internal Pull out
recovery
Loop Recovery
Take-up
Front Pull out
Discharge
No Loop Recovery
Internal Pull out
recovery
No Loop Recovery
Front Pull out
Discharge
Recovery Recovery
Invalid
Pull out
4. Note
Do not use ENQ, EOT, and ESC ACK SOH when automatic status is valid. Invalidate the automatic status in advance
using the DIPSW (memory switch) or the ESC RS a n command to query these.
―――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――
STAR Line Mode Command Specifications
Status
"0" "1"
-
-
-
-
(See table
below)
(See table
below)
(See table
below)
-
Presenter paper position state transition
Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper recovery) to Position 6 to Position 0
Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 7 to Position 0
Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 6 to Position 0
Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 7 to Position 0
Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 6 to Position 0
Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 7 to Position 0
Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 6 to Position 0
Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 7 to Position 0
Position 0 to Position 1 to (Paper cut) to Position 6
Position 0 to Position 1 to (Paper cut) to Position 6
5-12
TSP800 TSP700 TSP600 TUP900
Ver. 4.3 or Ver. 3.2 or Ver. 3.2 or Ver. 1.2 or
later later later later
- - -
NO NO NO OK
NO NO NO OK
- - -
NO NO NO OK
NO NO NO OK
NO NO NO OK
- - -
By model
TSP1000 TSP828L TSP700II
- - - -
NO NO NO
NO NO NO
- - - -
NO NO NO
NO NO NO
NO NO NO
- - - -
to Position 0
to Position 0
TSP650
-
NO
NO
-
NO
NO
NO
-