Maple Systems Silver Series Installation And Operation Manual page 168

164
Reserved Local Bit (LB) Table
Address Function
9000-9009 On after OIT reset
9010 Recipe Download Indicator
9011 Recipe Upload Indicator
Recipe Download/Upload
9012
Indicator
9013 Taskbar Touch indicator
9014 Taskbar CPU indicator
9015 Taskbar Alarm indicator
9016 Printer Error Indicator
9017 Printer Control Bit
9018,9019 Reserved for future use
9020 Message Board- Pen option
9021 Message Board- Brush option
9022 Message Board- Clip option
9023-9029 Reserved for future use
9030 Message Board- Pen width = 1
9031 Message Board- Pen width = 2
9032 Message Board- Pen width = 3
9033-9039 Reserved for future use
9040 Hide Fast SelectionWindow
9041 Hide TaskBar
9042 Hide TaskBar Buttons
Hide All (Fast Select,TaskBar,
9043
and TaskBarButtons)
Restore system parameters from
9044
recipe words
9045 Reset OIT
9046 Low Security Level
9047-9049 Reserved for future use
9050 Toshiba Protocol: T© control bit
TouchScreen Control during
9051
disabled backlight
1010-1001a, Rev 02
Access Description
These bits can be used for any object that needs to be initially set
R/W
when OIT is initialized.
RdOnly This bit is set when a recipe is downloading to the PLC
RdOnly This bit is set when a recipe is uploading from a PLC
RdOnly This bit is set when a recipe is download or uploaded to a PLC
RdOnly This bit is set when the touch indicator on the taskbar is pressed.
RdOnly This bit is set when the CPU indicator on the taskbar is pressed.
RdOnly This bit is set when the Alarm indicator on the taskbar is pressed.
RdOnly This bit is set when the OIT is unable to print to the printer.
This bit can be used to temporarily disable the printer port on the
OIT. Set the bit to disable the printer port. Clear the bit to
R/W enable.
Note: You must enable the printer option in the Edit...Set System
Parameters...General tab menu of EasyBuilder.
R/W Set this bit to select Pen mode for the Message Board feature
R/W Set this bit to select Brush mode for the Message Board feature
R/W Set this bit to select Clip mode for the Message Board feature
Set this bit to select Pen Width = 1 pixel for the Message Board
R/W
feature
Set this bit to select Pen Width = 2 pixels for the Message
R/W
Board feature
Set this bit to select Pen Width = 3 pixels for the Message Board
R/W
feature
Set this bit to hide the Fast Selection window; clear it to display
R/W
the Fast Selection window
Set this bit to hide the TaskBar window; clear it to display the
R/W
TaskBar window
Set this bit to hide the TaskBar buttons; clear it to display the
R/W
TaskBar buttons
Set this bit to hide the Fast Selection window, the TaskBar
R/W window, and the TaskBar buttons; clear it to display the three
objects
Set this bit ON will restore these system parameters from
R/W Reserved Recipe Word. After a restore, the system will clear this
bit off.
Write Set this bit ON to reset (warm boot) the OIT. After a reset, the
only OIT reboots and clears this bit.
Security Error: Latches to a 1 when there is an attempt to enter a
R/W higher security level page when the security level is not set. User
must clear it.
For Toshiba protocol driver. When this bit is on, write T© as ON
Or OFF T1/T1S user's manual. NOTE: In case of Timer/Counter
register write, the Timer/Counter's device data (2 bytes each)
R/W
corresponding to the Timer/Counter's register should be added.
If the Timer/Counter's device is set to ON, it should be '01'.
Otherwise, it should be 00.
R/W Set this bit to disable the touch screen when the backlight is off.
Sil ver Se ries In stal la tion & Op er a tion Man ual