Table of Contents
Advertisement
Quick Links
HMI5000B Series
Installation Guide
Introduction
Thank you for purchasing a Maple Systems HMI5000B Series graphic
industrial operator interface terminal. This booklet describes the steps
necessary for installing the following models:
HMI5040B
HMI5070B
HMI5070Bv3
HMI5100B
The HMI5000B Series touchscreens are configured using the
EasyBuilder Pro software.
For information on programming and configuring the HMI, please refer to
the EasyBuilder Pro Programming Manual (P/N 1010-1067) available
in the Support Center of the Maple Systems website.
For additional information, please refer to the Support Center section of
the Maple Systems website, www.maplesystems.com.
The Support Center provides links to information such as Software
Downloads, Manuals, FAQs, Technical Notes, Training Videos, Sample
Projects, Controller Information Sheets, Controller Cables and more.
1010-1051 Rev 03
www.maplesystems.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Maple Systems HMI5070Bv3
Summary of Contents for Maple Systems HMI5070Bv3
- Page 1 HMI5000B Series Installation Guide Introduction Thank you for purchasing a Maple Systems HMI5000B Series graphic industrial operator interface terminal. This booklet describes the steps necessary for installing the following models: HMI5040B HMI5070B HMI5070Bv3 HMI5100B The HMI5000B Series touchscreens are configured using the EasyBuilder Pro software.
-
Page 2: Unpacking The Unit
HMI5000B Series Touchscreen Power Connector Mounting Clamp Kit HMI5000B Series Installation Guide Warranty A copy of the Warranty and Limitation of Liability is contained in the product box. It can also be found on the Maple Systems website. 1010-1051 Rev 03 www.maplesystems.com... -
Page 3: Technical Support
Web: www.maplesystems.com Installation of HMIs Information furnished by Maple Systems is believed to be accurate and reliable. However, no responsibility is assumed by Maple Systems for the use of this information, or for any infringements of patents or other rights of third parties which may result from its use. -
Page 4: Environmental Considerations
Environmental Considerations The HMI is designed to operate in temperatures from 0° to 50°C (32° to 122°F), (HMI5070Bv3: 0° to 55°C). It is intended for indoor installations and may not be suitable for use in certain outdoor applications. Avoid installing the HMI in environments with severe mechanical vibration or shocks. -
Page 5: Control Panel Design Guidelines
Power Supply Selection The power supply used to power the HMI should provide an output of +10.5~28VDC (HMI5070Bv3: 24 ± 20% VDC) measured at the HMI power connector. A DC regulated power supply dedicated to the HMI is recommended. Use a power supply with adequate current rating. A... - Page 6 HMI5000B Installation Guide Figure 1: Typical Panel Layout 1010-1051 Rev 03 www.maplesystems.com...
-
Page 7: Control Panel Grounding
For a more in-depth overview of ground wiring techniques, refer to Technical Note #1027, “Ground Wiring and Electrical Noise Reduction” in the Technical Notes section of the Maple Systems website. Installation It is necessary to follow all installation procedures described in this chapter for electrical noise immunity and CE compliance. - Page 8 HMI. The power cable for the HMI should be 18AWG, 2-conductor wire with a shield drain wire and protective shield (foil/braid). Cable (P/N 6030-0009) may be purchased by the foot from Maple Systems for constructing power cables. Always run the DC ground wire directly back to the signal return of the power supply.
-
Page 9: Panel Preparation
Cutout dimensions for each particular HMI model are available for print and download from the Support Center-Dimensional Drawings section of the Maple Systems website. The area of the panel or mounting surface where the gasket comes into contact must be flat and free of scratches, pits, and other features that prevent the gasket from sealing properly. -
Page 10: Configuration Wiring
HMI5000B Installation Guide Configuration Wiring To configure the HMI using the EasyBuilder Pro software, use the Ethernet Configuration Cable (P/N 7431-0104). If using a switch or router between the PC and the HMI, use a straight- through or crossover cable as required by the switch or router. In order to download a project to the HMI over Ethernet, the HMI must be assigned a unique IP address that is on the same subnet as the development PC. - Page 11 D a ta + T X - T X + G N D T X D R T S C T S R X D HMI5070B / HMI5070Bv3 H M I5 07 0 B DE9P DE9S COM2 COM2 COM3 COM1...
- Page 12 Maple Systems Inc. 808 134 Street SW, Suite 120 Everett, WA 98204-7333 Phone: (425) 745-3229 Email: maple@maplesystems.com Web: www.maplesystems.com © 2019 Maple Systems Inc. All rights reserved. 1010-1051 Rev 03 www.maplesystems.com...
Need help?
Do you have a question about the HMI5070Bv3 and is the answer not in the manual?
Questions and answers