SSANGYONG RODIUS 2004.09 Manual page 103

3) CIRCUIT DESCRIPTION
(1) DOOR LOCK/UNLOCK BY DOOR LOCK SWITCH
- The door lock system outputs "LOCK"
driver's or passenger's door lock switch to lock position (while the driver's and
passenger's door lock switch is in "UNLOCK" position).
- The door lock system outputs "UNLOCK"
driver's or passenger's door lock switch to unlock position.
- "LOCK" or "UNLOCK" by the door lock switch is ignored when outputting the
"LOCK" or "UNLOCK" by other functions.
- The door lock/unlock system is not working regardless of the door lock switch positions
when connecting the battery.
- All door lock signals are "UNLOCK"
receiving the "LOCK" signal within 0.5 seconds (T3) after closing the driver's or
passenger's door. However, this operation is regardless of the ignition key positions.
(2) DOOR LOCK/UNLOCK BY CENTRAL DOOR LOCK
SWITCH
- The door lock system outputs "LOCK"
button on the central door lock switch.
- The door lock system outputs "UNLOCK"
"UNLOCK" button on the central door lock switch.
- The "LOCK" or "UNLOCK" inputs from the central door lock switch in armed mode
are ignored.
(3) DOOR LOCK/UNLOCK BY REMOTE CONTROL KEY
- The door lock system outputs "LOCK"
signal from the remote control key.
- The door lock system outputs "UNLOCK"
(T3) when receiving "UNLOCK" signal from the remote control key.
-
The door lock system outputs "UNLOCK"
when receiving "UNLOCK" signal again within 30 seconds (T1) after receiving the
first "UNLOCK" signal (second unlock step).
- The "second unlock step" is canceled when receiving "LOCK" signal within 30
seconds (T1) after receiving the first "UNLOCK"
for 0.5 seconds (T1) when positioning the
for 0.5 seconds (T2) when positioning the
for 0.5 seconds (T4) just for once when
for 0.5 seconds (T1) when pressing "LOCK"
for 0.5 seconds (T2) when pressing
for 0.5 seconds (T2) when receiving "LOCK"
signal for driver's door for 0.5 seconds
signal for all doors for 0.5 seconds (T3)
signal.
(4) AUTO DOOR LOCK
- The door lock system outputs "LOCK"
However, it doesn't output "LOCK" when all doors are locked or failed.
- If any of doors is unlocked after outputting "LOCK"
5 times (except step 1) with interval of one second.
- If any of doors is unlocked after 5 times of "LOCK"
"FAIL".
- If the door that was regarded as fail changes (UNLOCK →
one "LOCK" output will be done.
- If the door that was "LOCK" is changed to "UNLOCK", only one "LOCK" output will
be done. However, if it maintains unlock after lock output, the corresponding door will not
be regarded as fail.
- The door lock system outputs "UNLOCK"
conditions are established by this function or the key is cycled (IGN1=ON →
(even when there is no "Lock" output while the vehicle speed stays over 50 km/h
under lock condition).
However, when the ignition key is turned to "OFF"
- conditions will be cancelled.
The "FAIL" condition of the door will be erased when the ignition key is turned to
"OFF" position.
(5) AUTO DOOR UNLOCK (CRASH UNLOCK)
For conventional vehicles, G-sensor in RK STICS generates "UNLOCK"
collided over 15 km/h over vehicle speed. In this vehicle, the factory installed air bag module
transmits the collision signal to STICS to unlock the door.
- The air bag collision signal cannot be accepted within 7 seconds after turning the ignition
key to "ON" position.
- After this period, the door lock system outputs "UNLOCK"
seconds (T2) from 0.4 seconds (T2) after receiving the air bag collision signal.
- Even though the key is turned to "OFF"
the output continues on for remaining period.
- After input of the air bag collision signal, the door lock system doesn't
"UNLOCK" even when turning the ignition key to "ON" position.
0-59
8710-03
when the vehicle speed stays over 50 km/h.
in step 1, outputs "LOCK" up to
outputs, the door is regarded as
LOCK) to unlock, only
automatically if the "LOCK" output
OFF)
position, the lock output
signal when
for all doors for 5
position during the output of "UNLOCK",
output
CIRCUIT
RODIUS 2004.09