Help Codes; Help Mode Submenu - Maytag 30 Series Service Manual

HeLP CODeS

Help
Code
0F Oversuds detected during cycle, and washer
was not able to resolve an unbalance
condition detected during the final spin related
to the oversuds detection (via pressure
sensor) earlier in the cycle.
video note: SudS and 0 minutes alternating
on display while door is unlocked happens
when excess suds is detected in the final spin
and washer could not reach spin speeds. This
display continues after cycle is aborted. SudS
is displayed on screen for 2 minutes or until
the door is closed, whichever happens sooner.
32 More than 6 unbalance retries during the final
spin – spin (and cycle) has been aborted
33 Oversuds detected during wash cycle, and
washer was not able to resolve the condition
– cycle has been aborted. Washer unable
to sense that water has been fully drained
within required time, sensing as an oversuds
condition.
video note: SudS and 0 minutes alternating
on display with door locked happens when
cycle is aborted after the second drain,
because washer is unable to get rid of excess
suds. Door will remain locked for approx. 3
min. (shortened in video) then door unlocks,
this continues until the door is opened. SudS
is displayed on screen for 2 minutes or until
the door is closed, whichever happens sooner.
71 Generation 2 debit card cycle polling message
out of sequence
74 Generation 2 debit card remaining balance
message out of sequence
75 Generation 2 debit card new card balance
message out of sequence
88 Invalid messaging state found in data
acquisition communications
comm_suprv ( ) routine
Display flashing "unBaLanCe" at end of cycle when
the preceding cycle was aborted due to an unbalanced
load, see videos below:
Aborted cycle - customer leaves door open.
Aborted cycle - customer closes door.
Description

HeLP MODe SuBMenu

Step Display
Indication
1 1h.XX
2 2h.XX
3 3h.XX
4 1.X##
5 2.X##
6 3.X##
7 4.X##
8 SC.XX
9 EC.XX
10 SU.XX
11 EU.XX
12
.XXX
SPIN
13 P.XXX
14 U.XXX
* To erase the 3 help codes, press QUICK CYCLE button.
** The Errors displayed in this section are the history errors that have
occurred in the washer (not necessarily an error that is in progress).
The current error is displayed in the MANUAL KEY FUNCTION IN
DIAGNOSTIC SUB-MODE.
*** The values 255 and 254 are reserved numbers for specific cases.
(255=unbalance has not been calculated yet, 254=unbalance could
not be calculated.)
6-12
Explanation
Help Code 1, where XX is the
help code number.*
Help Code 2, where XX is the
help code number.*
Help Code 3, where XX is the
help code number.*
Error history code 1, where X is
the F or d code, and ## is the
code number.**
Error history code 2, where X is
the F or d code, and ## is the
code number.**
Error history code 3, where X is
the F or d code, and ## is the
code number.**
Error history code 4, where X is
the F or d code, and ## is the
code number.**
CCU software revision, where
XX is the software revision
number.
CCU EEPROM revision, where
XX is the EEPROM revision
number.
UI software revision , where XX
is the software number.
UI EEPROM revision, where
XX is the EEPROM number.
XXX is the current speed of the
drum, displayed in rpm.
The relative amount of power
requested by the motor, where
XXX is the value in watts.
The unbalance in the system,
where XXX is the unbalance
value.***