Maytag 30 Series Service Manual page 26

CODE
J . C 8
COIN/DEBIT OPTION
J . C 8
Both coin & debit selected.
J . C 8
Coins selected, debit disabled. Press the QUICK CYCLE key pad
3 consecutive times to change this selection.
J . C 8
PR models factory default to J._d. Debit Card selected, coins
disabled. Press the QUICK CYCLE key pad 3 consecutive times
to change this selection.
J . E 8
Enhanced Debit is self-selected when a Generation 2 card reader
is installed in the washer. The Ed option cannot be manually
selected or deselected.
� Press the DELICATES AND KNITS key pad once to advance to next code.
L . 0 0 PRICE SUPPRESSION OPTION
This option causes the customer display to show 'ADD' or
'AVAILABLE' rather than the amount of money to add. (Used
mainly in debit installations.)
L . 0 0 Not Selected 'OFF'.
L . PS
Selected 'ON'. Press the QUICK CYCLE key pad once
for this selection.
� Press the DELICATES AND KNITS key pad once to advance to next code.
8. C E CLEAR ESCROW OPTION
When selected, money held in escrow for 30 minutes without
further escrow or cycle activity will be cleared.
8.00
Not selected 'OFF'.
8. C E
Selected 'ON'. Press the QUICK CYCLE key pad once to change
this selection.
� Press the DELICATES AND KNITS key pad once to advance to next code.
8. 800
TOP SPIN SPEED RPM
8. 800
This can be selected from the following spin speeds: 600 rpm,
750 rpm, 800 rpm, 1000 (displays as 999) rpm. Step between
speeds by pressing the PERM. PRESS key pad. Factory
default of 800 rpm.
� Press the DELICATES AND KNITS key pad once to advance to next code.
0. 0 0 PENNY INCREMENT OFFSET
0. 0 0
This represents the penny increment price offset used in
Generation 2 (Enhanced Debit) PR models. Choose from 0-4
pennies by pressing the PERM. PRESS key pad.
� Press the DELICATES AND KNITS key pad once to advance to next code.
8 1.00 PREWASH LENGTH
8 1.00
This is the number of minutes of PREWASH. Choose 0 to disable
the prewash or select between 2 and 7 minutes by pressing the
PERM. PRESS key pad.
� Press the DELICATES AND KNITS key pad once to advance to next code.
82.03 FINAL SPIN LENGTH
82.03
This is the number of minutes of final high speed spin. Choose
from 3-8 minutes by pressing the PERM. PRESS key pad.
� Press the DELICATES AND KNITS key pad once to advance to next code.
EXPLANATION
If cycle counter (9 0C) is selected, the
following is true:
1 00 Cycles in Hundreds
2 00 Cycles in Ones
This is "VIEW ONLY" and cannot be cleared.
Press the DELICATES AND KNITS button
once to advance to next code.
_____________________________________
If money counter (1.0C or 1.C0) is selected,
the following is true:
3 00 Dollars in Hundreds
4 00 Dollars in Ones
5 00 Number of Cents
END OF SET-UP PROCEDURES
_____________________________________
EXIT FROM MANUAL SET-UP MODE
PD Models: Reinstall service access door
n
n PR Models: Remove Smart Card
PR Models without card reader installed:
n
Ë Unplug washer or disconnect power.
Ë Open console, reinsert plug into AA1,
close console.
Ë Plug in washer or reconnect power.
n PR Models set up as PN with programming
switch: Turn key clockwise and remove.
PR Models set up as PN without
n
programming switch: Set-up mode can be
exited by using procedures from Service
Access Code (See page 3-4).
3-8
1 02 = 200
2 25 = 25
TOTAL CYCLES = 225
3 01 = $ 100.00
4 68 = $ 68.00
5 75 = $ .75
TOTAL = $ 168.75