Canon Saddle Finisher-T2 Service Manual page 12

Contents
3.4.2.3 Removing the Escape Tray Cover ..................................................................................................... 3- 72
3.4.2.4 Removing the Front Inside Upper Cover........................................................................................... 3- 72
3.4.2.5 Removing the Grate-shaped Upper Guide......................................................................................... 3- 72
3.4.2.6 Removing the Tray 1 ......................................................................................................................... 3- 72
3.4.2.7 Removing the Tray 2 ......................................................................................................................... 3- 74
3.4.2.8 Removing the Grate-shaped Lower Guide ........................................................................................ 3- 75
3.4.2.9 Removing the Stapler......................................................................................................................... 3- 75
3.4.2.10 Removing the Processing Tray ........................................................................................................ 3- 76
3.4.2.11 Removing the Swing Unit Static Charge Eliminator....................................................................... 3- 77
3.4.3 Static Charge Eliminator 2 ........................................................................................................................ 3- 78
3.4.3.1 Removing the Front Door .................................................................................................................. 3- 78
3.4.3.2 Removing the Escape Tray Cover ..................................................................................................... 3- 78
3.4.3.3 Removing the Inlet Static Charge Eliminator.................................................................................... 3- 78
3.4.4 Static Charge Eliminator 3 ........................................................................................................................ 3- 78
3.4.4.1 Removing the Escape Door ............................................................................................................... 3- 78
3.4.4.2 Removing the Escape Delivery Static Charge Eliminator................................................................. 3- 79
3.4.5 Saddle Stitcher Controller PCB................................................................................................................. 3- 79
3.4.5.1 Removing the PCB Cover.................................................................................................................. 3- 79
3.4.5.2 Removing the Saddle Stitcher Controller PCB.................................................................................. 3- 79
Chapter 4 Maintenance
4.1 User Maintenance .............................................................................................................................................. 4- 1
4.1.1User Maintenance (Finisher Unit) ............................................................................................................... 4- 1
4.1.2User Maintenance (Saddle Stitcher Unit) .................................................................................................... 4- 1
4.2 Maintenance and Inspection .............................................................................................................................. 4- 2
4.2.1 Periodically Replaced Parts......................................................................................................................... 4- 2
4.2.1.1 Periodically Replaced Parts (Finisher Unit) ........................................................................................ 4- 2
4.2.1.2 Periodically Replaced Parts (Saddle Stitcher Unit) ............................................................................. 4- 2
4.2.2 Durables ...................................................................................................................................................... 4- 2
4.2.2.1 Durables (Finisher Unit) ...................................................................................................................... 4- 2
4.2.2.2 Durables (Saddle Stitcher Unit)........................................................................................................... 4- 3
4.2.3 Periodical Servicing .................................................................................................................................... 4- 3
4.2.3.1 Periodical Servicing (Finisher Unit) .................................................................................................... 4- 3
4.2.3.2 Periodical Servicing (Saddle Stitcher Unit)......................................................................................... 4- 3
4.3 Adjustment......................................................................................................................................................... 4- 4
4.3.1 Basic Adjustment ........................................................................................................................................ 4- 4
4.3.1.1 Upward Curl Mode .............................................................................................................................. 4- 4
4.3.1.2 Special Curl Mode ............................................................................................................................... 4- 4
4.3.1.3 Downward Curl Mode ......................................................................................................................... 4- 5
4.3.1.4 Heavy Paper Upward Curl Mode......................................................................................................... 4- 5
4.3.1.5 Stack Delivery Mode ........................................................................................................................... 4- 6
4.3.1.6 Offset Stack Mode ............................................................................................................................... 4- 6
4.3.1.7 Saddle Delivery Tray Limitless Mode ................................................................................................ 4- 7
4.3.2 Adjustment at Time of Parts Replacement.................................................................................................. 4- 7
4.3.2.1 Adjusting the Alignment Position ....................................................................................................... 4- 7
4.3.2.2 Adjusting the Staple Position............................................................................................................... 4- 8
4.3.2.3 Adjusting the Folding Position ............................................................................................................ 4- 8
4.3.2.4 Adjusting the Stitching Position (adjusting center stitching) ............................................................ 4- 10