Icom IC-9700 Basic Manual page 72
Vhf/uhf all mode transceiver
Hide thumbs
Also See for IC-9700:
- Advanced manual (173 pages) ,
- Service manual addendum (163 pages) ,
- Service manual (93 pages)
Table of Contents
Advertisement
8
SET MODE
Display (Continued)
» SET > Display
MENU
Display Language
Set the screen display language type to English or
Japanese.
L This item is displayed only when the "System Language"
is set to "Japanese."
System Language
Set the system language of the transceiver.
• English:
The system language of the transceiver
is English.
Only alphabetical characters (A to Z, a to
z, 0 to 9) and symbols (! " # $ % & ' ( ) * +
, - . / : ; < = > ? @ [ \ ] ^ _ ` { | } ~) can be
displayed. If Japanese characters (Kanji,
Hiragana and Katakana) are included,
the display shows "=" or "_" instead of
that character. In that case, you can only
delete "=" or "_" in the transceiver's edit
mode.
• Japanese: The system language of the transceiver
is Japanese.
Kanji, Hiragana and Katakana
characters, and the 2-bytes symbols can
be displayed. To display such characters
in the DR screen or Menu mode, set
"Display Language" to "Japanese."
L When this item is set to "English," "Display Language" is
not displayed.
(Default: English)
(Default: English)
8-17
When you set the system language of the
transceiver to Japanese, the IC-9700 has the
capability to display both English and Japanese
characters. HOWEVER, if you select Japanese, all
menu items throughout the IC-9700 system will be
displayed in only Japanese characters. There will
be no English item names. Unless you are fluent in
reading Japanese characters, use this feature with
extreme caution.
If you have change the IC-9700's language to
Japanese, and do not understand the menu system
in the new setting, you will have to change the
language back to English by doing a partial reset of
the IC-9700 CPU. A partial reset will not clear your
call sign databases.
To do a partial reset of the CPU, do the following steps:
1. Push [MENU].
2. Touch <SET>.
3. Touch the item (with the "etc" icon) shown below.
4. Touch the bottom item shown below.
5. Touch the upper item shown below.
6. The dialog is displayed as shown below. Touch
the left item.
The transceiver displays "PARTIAL RESET," then
the partial reset is completed.
- Quick Links:
- Rear Panel
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the IC-9700 and is the answer not in the manual?
Questions and answers
Hi I cannot get my ic7900 to work on independe freq and green light sub is on plus I got main rev and sub in my screen .and cannot get my transceiver work with DUB function.on 2 meter please can you help ?
To resolve the issue where the Icom IC-9700 is not working on an independent frequency with the green Sub light on and the Dualwatch (DUB) function not functioning on 2 meters:
1. Confirm Dualwatch is Enabled: Hold down the OFF button for 1 second to turn the Dualwatch function ON. This activates independent monitoring of both Main and Sub bands.
2. Select the Proper Band: Touch the grayed frequency readout to select the active band. Ensure the Main and Sub bands are set to different frequencies and not both on 2 meters, as the same frequency cannot be set on both bands.
3. Check Band Settings: Ensure that the Sub band is not set to the same frequency or band as the Main. The IC-9700 supports independent operation on different bands, but not the same frequency on both Main and Sub.
4. Verify TX is on Main Band: Transmission is only possible on the Main band (except in Split Frequency mode), so ensure the Main band is the one you intend to transmit on.
5. Check for Mode Compatibility: Some functions only apply to the selected band and mode. Confirm that the correct mode (FM, SSB, etc.) is selected for the band in use.
Following these steps should allow independent frequency operation with Dualwatch enabled.
This answer is automatically generated