Icom IC-9700 Basic Manual page 13
Vhf/uhf all mode transceiver
Hide thumbs
Also See for IC-9700:
- Advanced manual (173 pages) ,
- Service manual addendum (163 pages) ,
- Service manual (93 pages)
Table of Contents
Advertisement
#3
#2
#1
#0
@9
@8
@7
#2
#1
#0
@9
@8
@7
!9 OVF ICON
Displayed when an excessively strong signal is
received.
@0 PREAMPLIFIER/ATTENUATOR ICONS
/
Displayed when one the Preamplifi ers is ON, or the
Attenuator is ON.
@1 NOTCH INDICATOR
Displays "AN" when the Auto Notch function is ON,
and "MN" is displayed when the Manual Notch
function is ON.
@2 NOISE BLANKER/TONE/DIGITAL SQUELCH
ICONS
/
Displayed when the Noise Blanker function is ON,
when various tone functions are ON, or when
various digital squelch functions are ON.
@3 NOISE REDUCTION/AUTO TUNE INDICATORS
Displays "NR" when the Noise Reduction function is
ON.
Displays "AUTOTUNE" when the Auto Tuning
function is ON.
@4 EMR/BK/PACKET LOSS/AUTO REPLAY ICONS
/
/ / /
Displayed when the EMR (Enhanced Monitor
Request) function is ON, when the BK (Break-in)
function is ON, when Packet loss has occured, or
when the Automatic Reply function is ON.
@5 AGC ICON
(p� 3-9)
Displayed while the Auto Gain Control (AGC) is ON.
!9
@0
@1
@2
@6 AFC/
"
Control (AFC) is ON.
"
ON. (p. 3-5)
@7 MULTI-FUNCTION METER (p� 3-11)
Displays various values and levels, depending on
the function that you selected.
@8 RX STATUS INDICATOR
Lights green when a signal is received, or the
squelch is open.
@9 RF GAIN ICON
Displayed when
counterclockwise from the 11 o'clock position. The
icon indicates that the RF gain is reduced.
#0 MAIN BAND FREQUENCY READOUT
SUB BAND FREQUENCY READOUT (p� 3-4)
Displays the transmit or receive frequency for the
Main and Sub bands.
#1 IF FILTER INDICATOR
Displays the selected IF fi lter number.
#2 MODE INDICATOR
Displays the selected operating mode.
#3 TX STATUS INDICATOR
Displays the transmit status of the displayed
frequency.
•
•
outside of the band edge frequency range.
•
TX
1-5
PANEL DESCRIPTION
@3
@4
@5
/
ICON
/
(p� 8-5)
1
4
" is displayed while the Auto Frequency
" is displayed while the 1/4 Tuning function is
(p� 3-10)
(outer) is set to the
AF
RF/SQL
(p� 4-4)
(p� 3-3)
is displayed while transmitting.
is displayed when the selected frequency is
is displayed when transmission is inhibited (p. 3-10)
1
1
2
3
@6
4
!9
@0
5
@1
@2
6
@3
@4
@5
7
@6
8
9
10
11
12
13
14
15
16
17
18
19
20
21
- Quick Links:
- Rear Panel
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the IC-9700 and is the answer not in the manual?
Questions and answers
Hi I cannot get my ic7900 to work on independe freq and green light sub is on plus I got main rev and sub in my screen .and cannot get my transceiver work with DUB function.on 2 meter please can you help ?
To resolve the issue where the Icom IC-9700 is not working on an independent frequency with the green Sub light on and the Dualwatch (DUB) function not functioning on 2 meters:
1. Confirm Dualwatch is Enabled: Hold down the OFF button for 1 second to turn the Dualwatch function ON. This activates independent monitoring of both Main and Sub bands.
2. Select the Proper Band: Touch the grayed frequency readout to select the active band. Ensure the Main and Sub bands are set to different frequencies and not both on 2 meters, as the same frequency cannot be set on both bands.
3. Check Band Settings: Ensure that the Sub band is not set to the same frequency or band as the Main. The IC-9700 supports independent operation on different bands, but not the same frequency on both Main and Sub.
4. Verify TX is on Main Band: Transmission is only possible on the Main band (except in Split Frequency mode), so ensure the Main band is the one you intend to transmit on.
5. Check for Mode Compatibility: Some functions only apply to the selected band and mode. Confirm that the correct mode (FM, SSB, etc.) is selected for the band in use.
Following these steps should allow independent frequency operation with Dualwatch enabled.
This answer is automatically generated