Icom IC-9700 Basic Manual page 67

» SET > Connectors > USB AF/IF Output
MENU
Output Select
Selects the signal output from [USB].
• AF: An AF signal is output.
• IF: A 12 kHz IF signal is output.
AF Output Level
Sets the AF output level of [USB], when "Output
Select" of USB is set to "AF."
AF SQL
Selects whether or not to output the audio from [USB],
according to the squelch state, when "Output Select"
of USB is set to "AF."
• OFF (Open): The squelch is always opened
regardless of the transceiver's squelch
level.
• ON: The squelch opens and closes,
according to the transceiver's squelch
level.
AF Beep/Speech��� Output
Sets the Beep and Speech audio output setting of
[USB], when "Output Select" of USB is set to "AF."
• OFF: The beep and speech audio are not output.
• ON: The beep and speech audio are output.
IF Output Level
Sets the IF output level of [USB], when "Output
Select" of USB is set to "IF."
» SET > Connectors > LAN AF/IF Output
MENU
Output Select
Selects the signal output from [LAN].
• AF: An AF signal is output.
• IF: A 12 kHz IF signal is output.
AF SQL
Selects whether or not to output the audio from [LAN],
according to the squelch state, when "Output Select"
of LAN is set to "AF."
• OFF (Open): The squelch is always opened
regardless of the transceiver's squelch
level.
• ON: The squelch opens and closes,
according to the transceiver's squelch
level.
(Default: AF)
(Default: 50%)
(Default: OFF (Open))
(Default: OFF)
(Default: 50%)
(Default: AF)
(Default: ON)
8-12
» SET > Connectors > MOD Input
MENU
ACC MOD Level
USB MOD Level
LAN MOD Level
Sets the modulation input level of each interface.
DATA OFF MOD
DATA MOD
In the SSB, AM, or FM mode, selects the connector(s)
to input the modulation signal when the data mode is
OFF, or ON.
» SET > Connectors > ACC SEND Output
MENU
144M
430M
1200M
Selects whether or not to switch the SEND terminal
output level of [ACC] to the Low level during
transmitting.
• OFF: Does not switch to the Low level.
• ON: Switches to the Low level.
» SET > Connectors > USB SEND/Keying
MENU
TIP:
This is the setting for the terminal used for data
communication when you operate the transceiver
from the software on the PC.
When you connect the transceiver to a PC with a
USB cable, 2 COM ports are recognized on the PC.
To confirm USB (A)/USB (B), open the COM port
properties, and confirm the "Value" of the "Details" tab.
USB SEND
Sets the USB terminal of the transceiver to receive the
SEND signal from the software on the PC.
Select the same terminal as the terminal set by the
software.
L You cannot select the terminal which is already selected in
the "USB Keying (CW)" or "USB Keying (RTTY)" item.
USB Keying (CW)
Sets the USB terminal of the transceiver to receive the
CW Keying signal from the software on the PC.
Select the same terminal as the terminal set by the
software.
L You cannot select the terminal which is already selected in
the "USB SEND" or "USB Keying (RTTY)" item.
USB Keying (RTTY)
Sets the USB terminal of the transceiver to receive the
RTTY Keying signal from the software on the PC.
Select the same terminal as the terminal set by the
software.
L You cannot select the terminal which is already selected in
the "USB SEND" or "USB Keying (CW)" item.
8
SET MODE
(Default: 50%)
1
(Default: 50%)
(Default: 50%)
2
3
(Default: MIC,ACC)
(Default: ACC)
4
5
6
(Default: ON)
7
(Default: ON)
(Default: ON)
8
9
10
11
12
13
14
15
16
(Default: OFF)
17
18
19
(Default: OFF)
20
21
(Default: OFF)