Icom IC-9700 Basic Manual page 4
Vhf/uhf all mode transceiver
Hide thumbs
Also See for IC-9700:
- Advanced manual (173 pages) ,
- Service manual addendum (163 pages) ,
- Service manual (93 pages)
Table of Contents
Advertisement
ABOUT THE TOUCH SCREEN
D Touch operation
In the Advanced manual or Basic manual, the touch
operation is described as shown below, with the beep
tone ON.
Touch
If the display is touched briefly, one short beep
sounds.
Touch for 1 second
If the display is touched for 1 second, one
short and one long beep sound.
D Touch screen precautions
• The touch screen may not properly work when the
LCD protection film or sheet is attached.
• Touching the screen with your finger nails, sharp
topped object and so on, or touching the screen
hard may damage it.
• Tablet PC operations such as flick, pinch in and
pinch out cannot be performed on this touch screen.
D Touch screen maintenance
• If the touch screen becomes dusty or dirty, wipe it
clean with a soft, dry cloth.
• When you wipe the touch screen, be careful not to
push it too hard or scratch it with your finger nails.
Otherwise you may damage the screen.
VOICE CORDING TECHNOLOGY
The AMBE+2™ voice coding Technology embodied in this product is protected by intellectual property rights
including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology
is licensed solely for use within this Communications Equipment.
The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse
engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable
form.
U.S. Patent Nos.
#8,595,002, #8,359,197, #8,315,860, #8,200,497, #7,970,606, #6,912,495 B2.
ABOUT THE MANUALS
The following manuals or Guide for this transceiver
are published at the following internet address:
http://www.icom.co.jp/world/support/
• Advanced Manual (English)
Instructions for advanced operations in English.
• Basic Manual (English)
Instructions for basic operations, the same as this
manual.
• Basic Manual (Multi-language)
Instructions for basic operations in multiple
languages.
• CI-V Reference Guide (English)
Describes the control commands used in remote
control operation (serial communication with CI-V).
For Reference
• HAM Radio Terms (English)
A glossary of HAM radio terms in English.
To read the manuals or Guide, Adobe
Reader
®
is required. If you have not installed it,
please down load the Adobe
install it to your PC. You can download it from Adobe
Systems Incorporated's website.
A PC with the following Operating System is required.
• Microsoft
®
Windows
• Microsoft
®
Windows
• Microsoft
®
Windows
iii
®
Acrobat
®
Acrobat
®
Reader
®
10
®
8.1
®
7
®
®
and
- Quick Links:
- Rear Panel
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the IC-9700 and is the answer not in the manual?
Questions and answers
Hi I cannot get my ic7900 to work on independe freq and green light sub is on plus I got main rev and sub in my screen .and cannot get my transceiver work with DUB function.on 2 meter please can you help ?
To resolve the issue where the Icom IC-9700 is not working on an independent frequency with the green Sub light on and the Dualwatch (DUB) function not functioning on 2 meters:
1. Confirm Dualwatch is Enabled: Hold down the OFF button for 1 second to turn the Dualwatch function ON. This activates independent monitoring of both Main and Sub bands.
2. Select the Proper Band: Touch the grayed frequency readout to select the active band. Ensure the Main and Sub bands are set to different frequencies and not both on 2 meters, as the same frequency cannot be set on both bands.
3. Check Band Settings: Ensure that the Sub band is not set to the same frequency or band as the Main. The IC-9700 supports independent operation on different bands, but not the same frequency on both Main and Sub.
4. Verify TX is on Main Band: Transmission is only possible on the Main band (except in Split Frequency mode), so ensure the Main band is the one you intend to transmit on.
5. Check for Mode Compatibility: Some functions only apply to the selected band and mode. Confirm that the correct mode (FM, SSB, etc.) is selected for the band in use.
Following these steps should allow independent frequency operation with Dualwatch enabled.
This answer is automatically generated