Dv/Dd Set - Icom IC-9700 Basic Manual

DV/DD Set

» SET > DV/DD Set
MENU
Standby Beep (Default: ON (to me:Alarm/High Tone)
Turns the Standby Beep function ON or OFF.
This function sounds a beep after a received signal
disappears, in the DV mode.
• OFF: Does not sound a beep after a received signal
disappears.
• ON: Sounds a beep after a received signal
disappears.
• ON (to me:High Tone):
Sounds a high pitched beep when a received
signal that is addressed to your call sign (MY)
disappears.
When any other received signal disappears, a
regular beep sounds.
• ON (to me:Alarm/High Tone):
Sounds alarm (PiRoPiRoPiRo) when a
received signal that is addressed to your call
sign (MY) disappears.
When any other received signal disappears, a
regular beep sounds.
L The standby beep sounds even when "Key-Touch Beep"
is set to "OFF."
L The standby beep output level is depending on the Beep
level setting.
Auto Reply
Sets the Automatic Reply function to ON, OFF, Voice,
Position. This function automatically replies to a call
addressed to your own call sign, even if you are away
from the transceiver.
• OFF: Turns OFF the function.
• ON: Replies with your own call sign. (No audio
reply is sent)
• Voice: Replies with your call sign and any Auto
Reply message recorded on the SD (up to 10
seconds).
If no SD card is inserted, or no message is
recorded, only your call sign is transmitted.
The transmitted audio can be monitored.
L When "ON" or "Voice" is selected, the Automatic reply
function is automatically turned OFF when you push
or microphone's [PTT].
TRANSMIT
DV Data TX
Selects whether to manually or automatically transmit
data in the DV mode.
• PTT: Push or the microphone's [PTT] to
TRANSMIT
manually transmit data.
• Auto: When data is input from a PC through the
[DATA] jack, the transceiver automatically
transmits it.
MENU
Fast Data
Selects whether or not to use the DV Fast Data
function for data communication in the DV mode.
The DV Fast Data function uses the data and the
audio frames to send data approximately 3.5 times
faster than the normal speed. So, no audio can be
sent.
• OFF: Sends data at the slow speed (approximately
• ON:
L Even if "ON" is selected, when you push
or the microphone's [PTT], the data is sent at the slow
speed, because the audio frame is used for the audio
transmission.
The GPS data speed is set in "GPS Data Speed."
GPS Data Speed
Sets the GPS data speed when the data is sent using
the DV Fast Data function.
• Slow: Sends GPS data in the slow speed
• Fast: Sends GPS data in the fast speed
L When you send the GPS data to other transceivers that
can receive only slow speed data, set to "Slow."
TX Delay (PTT)
(Default: OFF)
Sets the TX delay time.
In this setting, you can set the time for the transceiver
sends the DV data using the DV Fast Data mode
when you push
microphone's [PTT].
OFF:
1 ~ 10sec: After pushing
NOTE: This function is usable only when "DV Data
TX" is set to "PTT."
MENU
(Default: Auto)
Digital Monitor
Select a receive mode when
mode.
• Auto:
• Digital:
• Analog: Receives in the FM mode.
8-6
» SET > DV/DD Set > DV Fast Data
950 bps).
Sends data at the fast speed (approximately
3480 bps).
(approximately 950 bps).
(approximately 3480 bps).
or hold down the
TRANSMIT
After pushing
TRANSMIT
[PTT], the transceiver returns to receive.
TRANSMIT
[PTT], the transceiver sends data using
the DV Fast Data mode for this set period.
When the TX data is completely sent
within this set period, the transceiver
automatically returns to receive.
» SET > DV/DD Set
XFC
Receives in the DV mode or the FM mode,
depending on the received signal.
Receives in the DV mode.
8
SET MODE
(Default: OFF)
1
2
3
4
5
TRANSMIT
6
7
8
(Default: Slow)
9
10
11
12
13
(Default: 2sec)
14
15
16
, or releasing
17
, or releasing
18
19
20
21
(Default: Auto)
is pushed in the DV