Extron electronics MKP 2000 User Manual page 39

Command
IP setup
Set MKP name
Set MKP name to factory
default
Query MKP name
Set date and time
Query date and time
X1%
KEY: = Name is 24 characters maximum. Upper and lower case alphanumeric characters and " " + – : = / and spaces
are valid.
X1^
= Default name = Factory default name (combination of the model name plus last three pairs of MAC address)
X1&
= Time and date (set) = MM/DD/YY-HH:MM:SS = MM = month: 01 (Jan.) — 12 (Dec.), DD = day: 01 through 31
YY = year: 00 through 99, HH = hour: 00 through 24, MM = minutes: 00 through 59, SS = seconds: 00 through 59
X1*
= Time and date (read) = Day,•DD•Mmm•YYYY•HH:MM:SS where: Day = weekday: Mon through Sun
DD = day: 01 through 31, Mmm = month: Jan through Dec, YYYY = year: 2000 through 2099,
HH = hour: 00 through 24, MM = minutes: 00 through 59, SS = seconds: 00 through 59
Set GMT offset
Query GMT offset
Set Daylight Savings Time
Query Daylight Savings Time
Set DHCP mode
Query DHCP mode
Set MKP IP address
Query MKP IP address
Query hardware MAC
address
Set subnet mask
Query subnet mask
Set gateway IP address
Query gateway IP address
NOTE: The set target IP parameters command can be issued with either the target IP address (
X2#
( ) variable, but not both. The response is as shown regardless of which variable is entered.
Set target (switcher) IP
parameters
Query target (switcher) IP
parameters
Set target (switcher)
password
NOTE: For the set target password command (
the user password.
X!
KEY:
= On/off status
X1(
= GMT offset
X2)
= Daylight Savings Time 0 = Daylight Savings Time off/ignore, 1 = Daylight Savings Time on (northern hemisphere),
X2!
= IP Address
X2@
= Hardware ( MAC) address (Example: 00-05-A6-##-##-##)
X2#
= Connection priority
X2$
= Password
ASCII Command Response
(host to unit) (unit to host)
}
E X1%
CN Ipn
}
E
•CN Ipn •
} X1%]
E
CN
}
E X1&
CT Ipt•
} X1*]
E
CT
E X1( }
CZ Ipz•
E } X1(]
CZ
E X2) }
CX Ipx•
E } X2)]
CX
}
E X!
DH Idh•
E } X!]
DH
E X2! }
CI Ipi•
E } X2!]
CI
E } X2@]
CH
E X2! }
CS Ips•
E } X2!]
CS
E X2! }
CG Ipg•
E } X2!]
CG
E X2! E X2# }
or SI Sip
E } X2!
SI
E X2$ }
PI Spw
E X2$ }
PI
0 = off/disable, 1 = on/enable
–12.0 through +14.0. Hours and minutes removed from GMT
2 = Daylight Savings Time on (Europe), 3 = Daylight Savings Time on (Brazil)
(xxx.xxx.xxx.xxx)
0 = Primary, 1 = Secondary
12 digits, alphanumeric
X1%]
X1^]
X1*]
X1(]
X2)]
X!]
X2!]
X2!]
X2!]
X2! X2@ X2#]
* *
X2@ X2#]
* *
X2$ ]
X2$
), the password variable
MKP 2000 • Remote Control
Additional Description
X1% X1^
may be
MM/DD/YY-HH:MM:SS
The divider between hours and
minutes is a period.
Set the switcher to display the
local time as Daylight Savings
Time (+1 hour) in summer months.
X2!
) or the connection priority
SI = Set MKP mode
can be either the administrator or
31