Extron electronics ECP 1000 User Manual
  1. Manuals
  2. Brands
  3. Extron electronics Manuals
  4. Control Panel
  5. ECP 1000
  6. User manual
Extron electronics ECP 1000 User Manual

Extron electronics ECP 1000 User Manual

Event control panel
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
Extron Electronics, USA
Extron Electronics, Europe
1230 South Lewis Street
Beeldschermweg 6C
Anaheim, CA 92805
3821 AH Amersfoort
USA
The Netherlands
714.491.1500
+31.33.453.4040
www.extron.com
Fax 714.491.1517
Fax +31.33.453.4050
© 2002 Extron Electronics. All rights reserved.
Extron Electronics, Asia
Extron Electronics, Japan
135 Joo Seng Road, #04-01
Daisan DMJ Building 6F
PM Industrial Building
3-9-1 Kudan Minami
Singapore 368363
Chiyoda-ku, Tokyo 102-0074 Japan
+65.6383.4400
+81.3.3511.7655
Fax +65.6383.4664
Fax +81.3.3511.7656
User's Manual
ECP 1000
Event Control Panel
68-518-01
Printed in the USA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ECP 1000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Extron electronics ECP 1000

Summary of Contents for Extron electronics ECP 1000

  • Page 1 3821 AH Amersfoort PM Industrial Building 3-9-1 Kudan Minami 68-518-01 The Netherlands Singapore 368363 Chiyoda-ku, Tokyo 102-0074 Japan 714.491.1500 +31.33.453.4040 +65.6383.4400 +81.3.3511.7655 Printed in the USA www.extron.com Fax 714.491.1517 Fax +31.33.453.4050 Fax +65.6383.4664 Fax +81.3.3511.7656 © 2002 Extron Electronics. All rights reserved.

  • Page 2: Table Of Contents

    ..................3-3 Using the Menus ..............3-4 Changing the backlight intensity .......... 3-4 Performing a system reset ............ 3-5 Programming the ECP 1000 ..........3-5 Applying a Switch ..............3-6 Applying a cut ................ 3-6 Applying a dissolve ..............3-7 Applying a title ...............

  • Page 3: Chapter 1 • Introduction

    Table of Contents, cont’d ECP 1000 Event Control Panel Chapter One Introduction Features ECP 1000 • Table of Contents...

  • Page 4: Ecp 1000 Event Control Panel

    Introduction Introduction, cont’d The Extron ECP 1000 event control panel attaches to as many as ECP 1000 Event Control Panel three Extron SGS 408 seamless switchers to provide complete control of multiple screens in large staging applications. The ECP 1000 allows you to create simultaneous or synchronous wipes, dissolves, fades, and cuts on any combination of the attached screens.

  • Page 5: Rear Panel Features

    100VAC to 240VAC, operating at 50 or 60 Hz. Cooling fan — One fan cools the ECP 1000 unit. The filter can Projectors be removed and washed as needed. See page A-2 for instructions.

  • Page 6: Chapter 3 • Operation

    Installation, cont’d ECP 1000 Event Control Panel Chapter Three Operation Top Panel Controls Power-up Using the Menus Applying a Switch ECP 1000 • Installation...

  • Page 7: Top Panel Controls

    When the ECP 1000 is powered up, the following events occur: for two screens. The buttons in the two right columns are pre- • All lights on the ECP 1000 front panel turn on and then off, in programmed. All of the buttons are user-programmable.

  • Page 8: Using The Menus

    PROGRAM 1.0 SEC LIGHT RESET MODE The buttons on the top panel of the ECP 1000 are backlit to make them easier to see in rooms with low-level lighting. You Press Press Press can control the amount of light the buttons emit by doing the...

  • Page 9: Applying A Switch

    Do one of the following: and 3, press screen selection buttons 1 and 3. • To program the ECP 1000, use the SGS 408 Control You can select a screen selection only if it is backlit. Program. See chapter 4 for information. When you...

  • Page 10: Wipes

    From top to bottom to the center of the screen • From bottom to top • Starting in the center of the screen and moving out to the edges of the screen ECP 1000 • Operation ECP 1000 • Operation...

  • Page 11: Applying A Wipe

    1 and 2 light. If this is not the first time any effect has been selected since the ECP 1000 was first installed or since a system reset was performed, the screen selection buttons that were selected the last time an effect was applied will light.

  • Page 12: Chapter 4 • Control Software For Windows

    Operation, cont’d ECP 1000 Event Control Panel Chapter Four Control Software for Windows Installing the Software Starting the Software 3-12 ECP 1000 • Operation...

  • Page 13: Installing The Software

    Control Software for Windows Control Software for Windows, cont’d The SGS 408 Control Program (Extron part number 29-049-01) , which is used to configure the ECP 1000, is compatible with Windows 95/98 and Windows NT. It allows you to do the following: •...
  • Page 14 Control Software for Windows, cont’d ECP 1000 Event Control Panel Appendix Reference Information Maintenance and Upgrades Specifications Part Numbers ECP 1000 • Control Software for Windows...

  • Page 15: Maintenance And Upgrades

    Figure A-2 — Removing the cover Pry off Cover Filter Cover Lift the cover from the ECP 1000 unit, and place it next to the unit. Figure A-1 — Removing the fan filter Make sure you are electrically grounded before touching IC chips.

  • Page 16: Replacing Keycap Labels

    IC into the socket. will list the specific ICs. Reinstall the cover of the ECP 1000. Attach the power cord to the ECP 1000 and to the AC power source. Make sure the ECP 1000 is working correctly.

  • Page 17: Part Numbers

    RCP comm cable – 100’ (30.5 m) 26-519-03 RCP comm cable – 300’ (91.4 m) 26-519-04 SGS 408 Control Program 29-049-01 ECP 1000 User’s Manual 68-518-01 SGS 408 User’s Manual 68-520-01 RCP 1000 User’s Manual 68-519-01 ECP 1000 • Reference Information...
  • Page 18 In no event will Extron Electronics be liable for direct, indirect, Conservar las instrucciones • Conservar las instrucciones de seguridad Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento, para futura consulta.

Table of Contents