FUTABA T12K Instruction Manual page 132

●ON/OFF switch setting
Move the cursor to the switch item and
access the switch setup screen by pushing
the RTN button and select the switch and ON
direction.
*For a detailed description of the setting method, see [Switch
Setting Method] at the back of this manual.
*Always on when [--].
●Master channel setting
1. Move the cursor to the [MASTER] item and
push the RTN button to switch to the data
input mode.
Select the function by scrolling the Push dial.
*The display blinks.
Push the RTN button to change the function
and return to the cursor mode.
2. When you want to link this mixing with other
mixes, move the cursor to the [LINK] item and
push the RTN button to switch to the data
input mode.
Select the link mode, either [+] or [-], by
scrolling the Push dial.
*The display blinks.
Push the RTN button to set the link mode and
return to the cursor mode.
*Check to ensure that the link mode is functioning properly
by operating the mix accordingly.
*Master channel control can be set to activate based on
the amount of stick input, or VR input, neither of which
includes ATV, D/R, and mixing selection. In this case, the
switch setup screen is displayed by pushing the RTN button
with "H/W" selected in the function selection. Select master
channel control. (To terminate the "H/W" selection, select
the [--] display and push the RTN button.
●Slave channel setting
1. Move the cursor to the [SLAVE] item and
push the RTN button to switch to the data
input mode.
Select the function by scrolling the Push dial.
*The display blinks.
Push the RTN button to change the function
and return to the cursor mode.
2. When you want to link this mixing with other
mixes, move the cursor to the [LINK] item and
push the RTN button to switch to the data
input mode.
Select the link mode to [+] or [-] by scrolling
the Push dial.
*The display blinks.
Push the RTN button to set the link mode and
return to the cursor mode.
*Check the direction by actual operation.
<Model Menu (Common Functions)>
132
●Trim mode ON/OFF setting
1. When changing the trim mode, move the
cursor to the [TRIM] item and push the RTN
button to switch to the data input mode.
Select ON/OFF by scrolling the Push dial.
*The display blinks.
Push the RTN button to change the trim
mode ON/OFF and return to the cursor
mode.
*To incorporate the mixing from the master trim, select [ON].
If trim is not desired, select [OFF].
*Effective when a function is set in the master channel.
●Linear curve setting
[Rate setting]
1. Move the cursor to the mixing rate setting
item and push the RTN button to switch to
the data input mode.
Adjust the rate by scrolling the Push dial.
Initial value: 0%
Adjustment range: -100%~+100%
*When the RTN button is pushed for one second, the servo
operation position is reset to the initial value.
Push the RTN button to end adjustment and
return to the cursor mode.
2. Repeat this procedure for all other rates as
desired.
[Offsetting the curve horizontally in the vertical
or horizontal direction]
1. Move the cursor to the [OFFS] setting item
and push the RTN button to switch to the
data input mode.
Adjust the offset rate by scrolling the Push
dial.
Initial value: 0%
Adjustment range: -100%~+100%
*When the RTN button is pushed for one second, the servo
operation position is reset to the initial value.)
Push the RTN button to end the adjustment
and return to the cursor mode.
2. Repeat this procedure for the other direction.
●5-point curve setting
[Rate setting]
1. Move the cursor to the point rate setting item
you want to adjust and push the RTN button
to switch to the data input mode.
Adjust the rate by scrolling the Push dial.
Initial value: 0%
Adjustment range: -100%~+100%
*When the RTN button is pushed for one second, the servo
operation position is reset to the initial value.)
Push the RTN button to end the adjustment
and return to the cursor mode.
2. Repeat this procedure for each point as
desired.