Table of Contents
Advertisement
TELEMETRY : Servo sensor
The SBS-01S can monitor and display the in-
flight angle and internal temperature of up to two
S.BUS2 servos.
If you forget to connect the servo wiring during
fuselage assembly, or the servo was disconnected,
an alarm can be activated at the transmitter.
● Select [ANGLE #1] in the TELEMETRY screen and access the
setup screen shown below by pushing the RTN button.
● Select the function name
and return to the Linkage
menu by pushing the RTN
button or pushing the
HOME/EXIT button.
RETURN
● ↑ An upward arrow
indicates the alarm
will sound when the
angle reaches above
your set value.
● ↓ A downward arrow
indicates the alarm
will sound when the
angle reaches below
your set value.
●Angle alarm setting range -180 ～ +179.9°
(↑THRESHOLD > ↓THRESHOLD)
Alert setting when servo #1 angle increases
1. Set "↑ALERT" on the <ANGLE#1> screen to
ACT. Move the cursor to INH and push the RTN
button.
2. Select the ACT mode by scrolling the Push dial.
3. Push the RTN button. (To terminate the input
and return to the original state, push the S1
button.)
4. The angle at which an alarm is generated can
be set by selecting the angle display next to "↑
THRESHOLD" and pushing the RTN button. This
generates an alarm when the angle increases.
5. Adjust the rate by scrolling the Push dial.
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6. Push the RTN button. (To terminate the input
and return to the original state, push the S1
button.)
Connect Alarm setting
If you forget to connect the servo wiring during
fuselage assembly, or the servo was disconnected,
an alarm can be activated at the transmitter.
*This alarm and display is limited to the S.BUS
servos connected to the servo sensors.
118
<Functions of Linkage Menu>
[Angle]
When it's servo 2, select #2.
●Push the S1 button to advance to the next page.
*Alarm when the angle has decreased.
Displaying data from the S.BUS servo
*SBS-01S must be installed in the aircraft.
*It cannot be used in S-FHSS mode
● Displays the maximum/minimum data
after the transmitter is turned on.
●Displays the angle data
<Push Dial>
If the following types are selected, the
transmitter will vibrate during the warning.
TYPE 1
TYPE 2
TYPE 3
TYPE 4
Alert setting when servo #1 angle decreases
1. Select page 2 by pushing S1 from the
<ANGLE#1> screen and set " ↓ ALERT" to ACT.
2. Select the ACT mode by scrolling the Push
dial.
3. Push the RTN button. (To terminate the input
and return to the original state, push the S1
button.)
4.The angle at which an alarm is generated
can be set by selecting the numerical display
next to " ↓ THRESHOLD" and pushing the RTN
button. This sounds an alarm when the angle
decreases.
5. Adjust the rate by scrolling the Push dial.
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6. Push the RTN button. (To terminate the input
and return to the original state, push the S1
button.)
1. Set "CONNECTION" on the <ANGLE> screen to
ACT. Move the cursor to INH and push the RTN
button.
2. Select the ACT mode by scrolling the Push dial.
3. Push the RTN button.
Scrolling
● Moving cursor
● Selecting mode
● Adjusting value
● To input data mode
● Data is entered
● To next page
●Angle alarm setting range
-179.9 ～ +180°
(↑THRESHOLD > ↓THRESHOLD)
*Alarm when the angle has increased.
"Vibes" type
Advertisement
Table of Contents
