FUTABA T12FG Software Update

Program Mixing [PROG. MIXES]
An offset mode has been added to the program mixing function. "Offset mode" is a function which allows simultaneous offset control of up to 4 slave functions per
circuit.
Setting Methods
Activate the function.
1. Select [PROG.MIXES] at the model menu and call the setup screen by
pushing the EDIT button.
2. Use [MODE] setting to select the program mixing operation mode.
[MIXING] is the normal mixing mode and [OFFSET] is the offset mode.
3. Move the cursor to [INHIBIT] of the mixing No. set to the offset mode
and push the EDIT button. The setup screen is displayed.
*Shows the currently set
program mixing No.
Offset rate
Slave function
Slave No.
4. Press the S1 button. Page 5/5 is displayed.
Switch selection
Function ON/OFF
5. Move the cursor to the [STATUS] item and switch to the data input
mode by pushing the EDIT button.
6. Turn the dial to the left and right until [ACT] blinks, and then push the
EDIT button. To deactivate the function, switch to [INH].
ON/OFF switch selection
Press 'S1' to move the cursor to page five (5). This page will be utilized
to select the [STATUS] and the activation method for the offset mix(es).
Bring up the switch setup screen by pressing the EDIT button, then select
the switch and activation (ON) direction. For further information on how
to do so, please refer to the [Switch Selection Method] located elsewhere
in the T12FG manual.
Slave No. selection
Setting of the slave No. from 1 to 4 at pages 1/5 ~ 4/5 is displayed. When
the S1 button is pushed, the displayed slave No. is switched.
Slave function setting
Move the cursor to the [FUNCTION] item and switch to the data input
mode by pushing the EDIT button. Select the function by turning the dial
and then push the EDIT button.
T12FG Software Update
Function Modification Contents
(Version: 1.2, 1.3)
Operation mode
(normal/timer)
Delay setting
Servo speed
setting
Fine tuning VR setting
Offset rate setting
The function operation offset amount when the mixing switch is ON and OFF
can be set independently.
1. Move the cursor to the [ON] or [OFF] item and switch to the data input
mode by pushing the EDIT button.
2. Turn the dial to the left and right and set the offset rate when the switch
is ON or OFF
Initial setting : 0%
Setting range: -300 ~ +300%
3. After setting, switch to the cursor move mode by pushing the EDIT
button.
*At adjustment, the offset rate is reset to the initial value by pushing the EDIT button for 1
second
Fine tuning trim setting
Operation control [CTRL], operation mode [MODE], and rate
[RATE] adjustment is possible by [FINE TUNING] item. (For a
description of the setting method, refer to [Fine tuning trim
setting] at the back of the instruction manual.
Operation mode setting
The operation mode when the switch was operated is selected. Normal
mode [NORM] or timer mode [TIME] can be selected.
[Normal mode]
After the switch is set to ON, mixing is turned ON after the time set by start
delay ([START]) has elapsed. Similarly, after the switch was set to OFF,
mixing is turned OFF after the time set by stop delay ([STOP]) has
elapsed.
[Timer mode]
After the switch was set to ON, mixing is turned ON after the time set by
start delay ([START]) has elapsed. Mixing is automatically turned OFF
after the time set by stop delay ([STOP]) has elapsed. Examples of use
are jet plane and scale model retractable landing gear and cover linked
mixing, etc.
Servo speed setting
The speed at function operation can be adjusted. (For a description of the
setting method, refer to [Servo speed setting] at the back of the instruction
manual.)
Delay setting
Mixing operation at mixing switch ON ([START]) and OFF ([STOP]) can
be delayed by [DELAY] item. (When switch is set.)
1. Move the cursor to the [START] or [STOP] item and switch to the data
input mode by pushing the EDIT button.
2. Turn the dial left and right and set the mixing operation delay time at
switch ON or OFF.
Initial value : 0 sec
Setting range : 0 ~ 35 sec
3. After adjustment, switch to the cursor move mode by pushing the EDIT
button.
*At adjustment, the delay time can be reset to the initial value by
pushing the EDIT button for 1 second.
1
1M23N18907
[All model types]