Yamaha Star XVS13AA(C) 2011 Service Manual page 58

Item
Starter motor lead bolt (starter
relay side)
Battery terminal bolt
Battery box bolt
Battery box bracket bolt
Sidestand bracket bolt
Sidestand switch bolt
Sidestand nut
Rear brake master cylinder cover
bolt
Right rider footrest bracket nut
Rider footrest assembly bolt (left
and right)
Passenger footrest bolt (left and
right)
Shift rod locknut
Shift arm bolt
Brake fluid reservoir bolt
Horn bracket bolt
Coolant reservoir cover bracket
bolt
Locknut (rear brake master cylin-
der)
Rectifier/regulator cover bolt
Rectifier/regulator bolt
TIP
Lower ring nut
1. First, tighten the lower ring nut to approximately 52 Nm (5.2 m·kg, 37 ft·lb) with a torque wrench, then
loosen the lower ring nut completely.
2. Retighten the lower ring nut to 18 Nm (1.8 m·kg, 13 ft·lb) with a torque wrench.
TIP
Front wheel axle pinch bolt
1. Insert the front wheel axle from the right side and tighten it to 72 Nm (7.2 m·kg, 52 ft·lb).
Check that the left end of the front wheel axle is flush with the front fork. If necessary, manually push
the front wheel axle or lightly tap it with a soft hammer until its end is flush with the front fork. How-
ever, if the surface of the front wheel axle end is not parallel to the surface of the front fork, align a
point on the outer edge of the axle with the fork, making sure that the axle does not protrude past
the fork.
2. In the order pinch bolt "1" → pinch bolt "2" → pinch bolt "1", tighten each bolt to 20 Nm (2.0 m·kg, 14
ft·lb) without performing temporary tightening.
Thread
Q'ty
size
M6 1 4 Nm (0.4 m·kg, 2.9 ft·lb)
M6 2 7 Nm (0.7 m·kg, 5.1 ft·lb)
M6 4 7 Nm (0.7 m·kg, 5.1 ft·lb)
M6 5 7 Nm (0.7 m·kg, 5.1 ft·lb)
M10 2 56 Nm (5.6 m·kg, 40 ft·lb)
M5 2 4.0 Nm (0.4 m·kg, 2.9 ft·lb)
M10 1 64 Nm (6.4 m·kg, 46 ft·lb)
M8 2 23 Nm (2.3 m·kg, 17 ft·lb)
M8 2 16 Nm (1.6 m·kg, 11 ft·lb)
M10 4 48 Nm (4.8 m·kg, 35 ft·lb)
M8 4 23 Nm (2.3 m·kg, 17 ft·lb)
M6 2 7 Nm (0.7 m·kg, 5.1 ft·lb)
M6 1 16 Nm (1.6 m·kg, 11 ft·lb)
M6 1 7 Nm (0.7 m·kg, 5.1 ft·lb)
M8 1 30 Nm (3.0 m·kg, 22 ft·lb)
M6 2 7 Nm (0.7 m·kg, 5.1 ft·lb)
M8 1 16 Nm (1.6 m·kg, 11 ft·lb)
M6 2 7 Nm (0.7 m·kg, 5.1 ft·lb)
M6 2 7 Nm (0.7 m·kg, 5.1 ft·lb)
2-31
TIGHTENING TORQUES
Tightening torque Remarks
LT
LT
LT
LT
LT
LT