Intek Elite 16D Installation & Programming Manual page 65

P301E Zone 1 vibration sensitivity - Default 0
P302E Zone 2 vibration sensitivity - Default 0
P303E Zone 3 vibration sensitivity - Default 0
P304E Zone 4 vibration sensitivity - Default 0
P305E Zone 5 vibration sensitivity - Default 0
P306E Zone 6 vibration sensitivity - Default 0
P307E Zone 7 vibration sensitivity - Default 0
P308E Zone 8 vibration sensitivity - Default 0
P161E Zone 9 vibration sensitivity - Default 0
P162E Zone 10 vibration sensitivity - Default 0
P163E Zone11 vibration sensitivity - Default 0
P164E Zone 12 vibration sensitivity - Default 0
P165E Zone 13 vibration sensitivity - Default 0
P166E Zone 14 vibration sensitivity - Default 0
P167E Zone 15 vibration sensitivity - Default 0
P168E Zone 16 vibration sensitivity - Default 0
LOW ZONE ASSIGNMENTS (ZONES 1-8)
P331E Zone is a normally open/closed output - Default N/C
P332E Zone is a radio detector - Default 0ff
P333E Zone is in Area "A" - Default all
P334E Zone is in Area "B" - Default none ) If zone is in both it is then a partition "C" zone
P335E Zone is isolatable - Default all
P336E Zone is a handover - Default 2
P337E Two trigger zones -Default none
P338E Zone is 24Hr - Default none
P339E Monitor mode zones - Default zones 1-4
P340E Day zones - Default none
P341E Siren lockout zones - Default none
P342E Auto exclude zones - Default all
P343E Access control door position input - Default none
P344E Access control request to exit input - Default none
P345E Continuous day zone - Default none
P346E Zones 1-8 will report multiple activations Default on
HIGH ZONE ASSIGNMENTS (ZONES 9-16)
P351E Zone is a normally open/closed output - Default N/C
P352E Zone is a radio detector - Default 0ff
P353E Zone is in Area "A" - Default all
P354E Zone is in Area "B" - Default none ) If zone is in both it is then a partition "C" zone
P355E Zone is isolatable - Default all
P356E Zone is a handover - Default none
P357E Two trigger zones -Default none
P358E Zone is 24Hr - Default none
P359E Monitor mode zones - Default zones 1-4
P360E Day zones - Default none
P361E Siren lockout zones - Default none
P362E Auto exclude zones - Default all
P363E Access control door position input - Default none
P364E Access control request to exit input - Default none
P365E Exclusive day zone - Default none
P366E Zones 9-16 will report multiple activations-Default on
SYSTEM DELAYS & TIMERS
P401E Zone 1 entry delay - Default 20 sec
P402E Zone 2 entry delay - Default 20 sec
P403E Zone 3 entry delay - Default 0
P404E Zone 4 entry delay - Default 0
P405E Zone 5 entry delay - Default 0
P406E Zone 6 entry delay - Default 0
P407E Zone 7 entry delay - Default 0
P408E Zone 8 entry delay - Default 0
P409E Zone 9 entry delay - Default 0
P410E Zone 10 entry delay - Default 0
P411E Zone 11 entry delay - Default 0
P412E Zone 12 entry delay - Default 0
)
)
Page 65
0 = No vibration sensor
Sensitivity 1-8
1 = High sensitivity
8 = Low sensitivity
0ff = N/C On = N/O
0ff = N/C On = N/O
Delay timer values
0 = instant, no delay
1-999 = 1 -999 seconds
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 30
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 31
Page 32
Page 32
Page 32
Page 32
Page 32
Page 32
Page 32
Page 32
Page 32
Page 32
Page 32
Page 32