Contact Id Code Assignments; Alarm Voice Message Mapping - Intek Elite 16D Installation & Programming Manual

This block of addresses from P620E to P658E is used to assign the Ademco Contact ID codes to all of the
definable events your Elite V4 control communicator can report.
P620E XXXE Duress Alarm
P621E XXXE Zone 1 Activation
P622E XXXE Zone 2 Activation
P623E XXXE Zone 3 Activation
P624E XXXE Zone 4 Activation
P625E XXXE Zone 5 Activation
P626E XXXE Zone 6 Activation
P627E XXXE Zone 7 Activation
P628E XXXE Zone 8 Activation
P629E XXXE Zone 9 Activation
P630E XXXE Zone 10 Activation
P631E XXXE Zone 11 Activation
P632E XXXE Zone 12 Activation
P633E XXXE Zone 13 Activation
P634E XXXE Zone 14 Activation
P635E XXXE Zone 15 Activation
P636E XXXE Zone 16 Activation
P641E XXXE Zone 1 Low Tamper
P642E XXXE Zone 2 Low Tamper
P643E XXXE Zone 3 Low Tamper
P644E XXXE Zone 4 Low Tamper
P645E XXXE Zone 5 Low Tamper
P646E XXXE Zone 6 Low Tamper
P647E XXXE Zone 7 Low Tamper
P648E XXXE Zone 8 Low Tamper
P651E XXXE Zone 1 High Tamper
P652E XXXE Zone 2 High Tamper
P653E XXXE Zone 3 High Tamper
P654E XXXE Zone 4 High Tamper
P655E XXXE Zone 5 High Tamper
P656E XXXE Zone 6 High Tamper
P657E XXXE Zone 7 High Tamper
P658E XXXE Zone 8 High Tamper
ALARM VOICE MESSAGE MAPPING - P660E - P679E
This block of addresses is used to assign up to eight possible voice messages to the Panic alarm battery low and
16 zone activation's. More than one message can be assigned to each zone activation. The voice messages will
be replayed over the phone in response to an alarm activation to those phone numbers which have been assigned
Speech Dial format at options P231E to P236E More than one message may be assigned to an alarm event
however, if multiple messages are assigned to one event, the messages will be replayed in numerical order.
For example, if message #1 said "Fire" and message #5 said "Activation at Acme premises" and if both messages
were mapped to Zone 1 activation's (P661E15E) the replay message in response to a zone 1 activation would be
heard as "Fire alarm at Acme premises"
It is possible to map up to eight messages to an alarm event but it should be noted that they will always be replayed
in numerical order so when recording your messages into the speech module, you must organise the messages in
the correct order.
P660E 1-8E Voice Messages Mapped to Panic Alarm - Default 1
P661E 1-8E Voice Messages Mapped to Zone 1 Activation's - Default 1
Default = 121
Default = 130
Default = 130
Default = 130
Default = 130
Default = 130
Default = 130
Default = 130
Default = 130
Default = 130
Default = 130
Default = 130
Default = 130
Default = 130
Default = 130
Default = 130
Default = 130
Default = 137
Default = 137
Default = 137
Default = 137
Default = 137
Default = 137
Default = 137
Default = 137
Default = 137
Default = 137
Default = 137
Default = 137
Default = 137
Default = 137
Default = 137
Default = 137
Page 54
0 = No Report
0 = No Report
0 = No Report