Smart Dc Bi-Parting Gates: Dual Gate Wiring; Smart Dc Bi-Parting Gates: Photo Eye (Emx Irb Mon) - HySecurity UL 325 Quick Start - Supplemental Instructions

S dc b
mart
The following illustrates a photo eye connection for bi-parting Smart DC gate operators and the Installer Menu
configurations for each (Primary and Secondary).
NOTE: Turn OFF AC power before connecting sensor wires to Smart DC.
CAUTION
Connect all contact and non-contact sensors to same power source.
Example, Do NOT connect photo eyes to +24VDC and gate edges
to +12VDC. Incompatible electrical flow and FAULT 2 occurs.
COMMON and +24V
can be wired to
matching terminals
in Receiver
CAUTION
Set DIP
Switches
1 = OFF
2 = OFF
3 = OFF
4 = ON
TIP:
Jumper
POWER COM to
RELAY COM inside
receiver

Smart DC Bi-Parting Gates: Dual Gate Wiring

PRIMARY
Gate Operator
DG 2
46
D0726 Rev. J
-p G
I artInG ateS
NOTE: To align the
Photo Eye, access
PE (photo eye
alignment) via the
User Menu.
+24V
+24V
Shielded cable (3
wire)
UL 325 - 2016 HySecurity Monitored Sensors
: p e
Hoto ye
PRIMARY
Gate Operator
DG 2
COM
COM
COM
COM
COM
COM
COM
COM
STOP
OPEN
CLOSE
OPEN
P ARTIAL
11
SENSOR 2
OPEN
EYE
10
SENSOR 3
EXIT
EXIT 9
LOOP
LOOP
BLOCK
8
EXIT EXIT
IN OBS
7
LOOP
LOOP
OUT OBS
6
LOOP
LOOP
CENTER
5
LOOP
LOOP
EDGE 4
SENSOR 1
EYE
SENSOR
3
COM
COM
2
+ 24 V
EMERG
1
OPEN
SHOW
LEDs
+24V
CLOSE
OPEN
P ARTIAL
OPEN
EYE
EXIT
LOOP
EXIT
LOOP
LOOP
LOOP
EDGE
EYE
COM
EMERG
OPEN
Conduit
Supports low voltage cable
(emX Irb mon)
Installer Menu Settings
DG 2 (PRIMARY)
DUAL GATE
CLOSE MENU
OPEN STOP RESET
PREV NEXT SELECT
S1 2 (EYE CLOSE)
SENSOR #1 TYPE
OPEN CLOSE STOP MENU
S2 1 (NOT USED)
SENSOR #2 TYPE
PREV NEXT SELECT
OPEN CLOSE STOP MENU
S3 1 (NOT USED)
SENSOR #3 TYPE
SELECT
PREV NEXT
OPEN CLOSE STOP MENU
PREV NEXT SELECT
DG 1 (SECONDARY)
DUAL GATE
OPEN CLOSE
PREV NEXT
COM
COM
COM
S1 1 (NOT USED)
COM
SENSOR #1 TYPE
COM
COM
COM
OPEN
COM
STOP
PREV
OPEN
OPEN
11
SENSOR 2
PREV
10
SENSOR 3
9
EXIT
LOOP
OPEN
BLOCK
8
EXIT
IN OBS
7
LOOP
PREV
OUT OBS
6
LOOP
CENTER
5
LOOP
4
SENSOR 1
SENSOR
3
COM
2
+ 24 V
1
SHOW
LEDs
SECONDARY
Gate Operator
DG 1
NOTE: Connect ground shield
wire to one Controller, not both.
© 2016 www.hysecurity.com
RESET
RESET
RESET
SECONDARY
Gate Operator
DG 1
STOP MENU RESET
SELECT
CLOSE STOP MENU RESET
S2 1 (NOT USED)
SENSOR #2 TYPE
SELECT
NEXT
CLOSE STOP MENU RESET
S3 1 (NOT USED)
SENSOR #3 TYPE
NEXT SELECT
CLOSE STOP MENU RESET
NEXT SELECT