Smart Dc: Wireless Edge Gate Link And Photo Eye - HySecurity UL 325 Quick Start - Supplemental Instructions

S dc: w
mart
The wiring diagram illustrates a wireless edge receiver and a
photo eye connection. Refer to Photo Eye Alignment on page 12.
NOTE: Turn OFF AC power before connecting sensor wires to Smart DC.
EMX IRB MON Photo Eye
Transmitter
Connect all contact and non-
contact sensors to same power
source. Example, Do NOT
connect photo eyes to +24VDC
and gate edges to +12VDC.
Incompatible electrical flow.
A FAULT 2 appears.
COMMON / NEG. to SENSOR COM
CAUTION
Set DIP Switches
1 = OFF
2 = OFF
3 = OFF
4 = ON
NOTE: DIP switches must
be set as shown otherwise
the photo eye will not
operate correctly. For easy
photo eye alignment,
TIP:
Jumper
POWER COM to
RELAY COM
Miller Edge 2 Channel Wireless
Receiver (MGL - RX20)
COM
Green
POWER
* P / NC
10K
Yellow
STATUS COM
* P / NC
10K
CH 1 POWER
CH 2
Antenna
OUTPUT
SELECT
44
D0726 Rev. J
L e
Ire eSS dGe
CAUTION
Photo Eye
Transmitter
+24V
COMMON / NEG.
to SENSOR COM
+24V
To SENSOR COM
COM attaches to
SENSOR COM
*Sensor wire (P/ NC) can
attach to any SENSOR input.
CH 1 and CH 2 "LEARN" buttons.
amber light blinks continuously. Press the Edge or Test button on the Transmitter to complete
the LEARN mode process and sync the receiver and transmitter.
DIP switches for CH1 and CH2. Verify dip switch is set to "R" for each channel used. HySecurity uses NC
"Relay" sensors. Do NOT select "P" as the output. P = "Pulse" device.
UL 325 - 2016 HySecurity Monitored Sensors
G L
ate InK and
COM
COM
COM
COM
COM
COM
COM
COM
STOP
OPEN
CLOSE
OPEN
P ARTIAL
SENSOR 2
OPEN
EYE
SENSOR 3
EXIT
EXIT
LOOP
LOOP
BLOCK
EXIT
EXIT
IN OBS
LOOP
LOOP
OUT OBS
LOOP
LOOP
CENTER
LOOP
LOOP
EDGE
SENSOR 1
EYE
SENSOR
COM
COM
+ 24 V
EMERG
+24V
OPEN
All external entrapment protection sensors must be
NC sensor outputs and wired to the SENSOR COM
terminal for monitoring and powering purposes.
The sensor becomes actively powered when the
gate operator receives a run command.
Press the LEARN button on the Receiver for 2 seconds until the
p
Hoto
Installer Menu Settings
Configuring SENSOR 1
S1 0
SENSOR #1 TYPE
OPEN CLOSE
S1 1 (NOT USED)
PREV NEXT
SENSOR #1 TYPE
CLOSE
OPEN
PREV NEXT
Configuring SENSOR 2
S2 0
SENSOR #2 TYPE
OPEN CLOSE
S2 2 (EYE CLOSE)
PREV NEXT
SENSOR #2 TYPE
OPEN CLOSE
NEXT
PREV
Configuring SENSOR 3
11
S3 0
10
SENSOR #3 TYPE
9
OPEN CLOSE
8
S3 6 (EDGE BOTH)
7
PREV NEXT
SENSOR #3 TYPE
6
OPEN CLOSE
5
4
PREV NEXT
3
2
1
SHOW
LEDs
MGL - RX20
+24V
CAUTION
© 2016 www.hysecurity.com
e
ye
STOP MENU RESET
SELECT
MENU
STOP RESET
SELECT
STOP MENU RESET
SELECT
STOP MENU RESET
SELECT
STOP MENU RESET
SELECT
STOP MENU RESET
SELECT