Dadf Jam 6 Rap; Dadf Jam 7 Rap - Xerox phaser 3635 Service Manual

05-600 DADF Jam 6 RAP

05-600 The machine has detected that a DADF sensor is actuated when the machine is
switched on.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Refer to Wiring Diagram 10. Perform the following:
1. Open the DADF door assembly, PL 5.10 Item 3. Remove all jammed paper.
2. Remove all jammed paper from the DADF exit tray.
3. Check the document path for damage or obstructions.
4. Check that the following actuators move freely and are not damaged:
• Document detect sensor actuator, PL 5.30 Item 18.
• Paper length sensor actuator, PL 5.20 Item 9.
• Registration sensor actuator, PL 5.35 Item 10.
• Scan sensor actuator, PL 5.35 Item 6.
5. Enter dC330. Check the following sensors. Install new components as necessary:
• Code 05-100, document detect sensor (Q05-100), PL 5.30 Item 17.
• Code 05-120, paper length sensor (Q05-120), PL 5.20 Item 11.
• Code 05-130, registration sensor (Q05-130), PL 5.35 Item 7.
• Code 05-140, scan sensor (Q05-140), PL 5.35 Item 7.
6. Check the following wiring:
• Between the document detect sensor, and CN5 on the DADF PWB.
• Between the paper length sensor and CN10 on the DADF PWB.
• Between the registration sensor and CN1 on the DADF PWB.
• Between the scan sensor and CN1 on the DADF PWB.
7. If necessary, install new components:
• DADF PWB, PL 5.15 Item 16.
• Document transport assembly, PL 5.35 Item 14.
Status Indicator RAPs
05-600, 05-700

05-700 DADF Jam 7 RAP

05-700 The machine has detected that an oversize document has been fed.
Procedure
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Refer to Wiring Diagram 10. Perform the following:
1. Open the DADF door assembly, PL 5.10 Item 3. Remove all jammed paper.
2. Remove all jammed paper from the DADF exit tray.
3. Check that the customer is not attempting to feed documents outside of specification,
refer to GP 8 DADF Document Feeding Specifications.
4. Check the pickup roll assembly, PL 5.25 Item 2. If necessary, install a new pickup roll
assembly, PL 5.25 Item 2.
5. Check the retard pad assembly, PL 5.30 Item 2. If necessary, install a new retard pad, PL
5.30 Item 2.
6. Check that the registration sensor actuator, PL 5.35 Item 10 moves freely and is not dam-
aged.
7. Enter dC330 code 05-130. Check the registration sensor (Q05-130), PL 5.35 Item 7.
8. Check the wiring between the registration sensor and CN1 on the DADF PWB. If neces-
sary, install a new registration sensor, PL 5.35 Item 7.
9. If necessary, install new components:
• DADF PWB, PL 5.15 Item 16.
• Document transport assembly, PL 5.35 Item 14.
2-16
WARNING
Phaser 3635MFP
Draft 4