Alcatel-Lucent 7750 Reference Manual page 104

WLAN Gateway
Table 28: WLAN Gateway (description) (Continued)
Attribute ID Attribute Name
26-6527-188 Alc-Wlan-Dsm-
Ingress-Policer
26-6527-189 Alc-Wlan-Dsm-Egress-
Policer
26-6527-190 Alc-Wlan-Handover-
Ip-Address
26-6527-205 Alc-GTP-Default-
Bearer-Id
26-6527-206 Alc-Wlan-SSID-VLAN
26-6527-216 Alc-Datatrig-Lease-
Time
26-25053-2 Ruckus-Sta-RSSI
26-10415-1 3GPP-IMSI
26-10415-5 3GPP-GPRS-
Negotiated-QoS-Profile
Page 104
Specifies the name of a distributed subscriber management (DSM) ingress
policer configured under configure subscriber-mgmt wlan-gw distributed-
sub-mgmt dsm-policer <policer-name>. This policer will be applied to the
DSM UE. This overrides the value configured under configure service ies/
vprn <svc-id> subscriber-interface <subscriber-interface-name> group-
interface <group-interface-name> wlan-gw vlan-tag-ranges range start
<starting-vlan> end <ending-vlan> distributed-sub-mgmt ingress-policer.
Specifies the name of a distributed subscriber management (DSM) egress
policer configured under configure subscriber-mgmt wlan-gw distributed-
sub-mgmt dsm-policer <policer-name>. This policer will be applied to the
DSM UE. This overrides the value configured under configure service ies/
vprn <svc-id> subscriber-interface <subscriber-interface-name> group-
interface <group-interface-name> wlan-gw vlan-tag-ranges range start
<starting-vlan> end <ending-vlan> distributed-sub-mgmt egress-policer.
IP address provided in RADIUS Access-Accept message to signal handover
from LTE or UMTS to WIFI. If this VSA is present, handover indication is set
in GTP session creation request to PGW/GGSN.
When establishing a GTP connection for a UE, this specifies the bearer id
(GTPv2) or NSAPI (GTPv1) that will be used for the data path connection. If
not provided, a default value of 5 will be used.
The VLAN is transparently taken from the UE's Ethernet layer and can be
reflected in both authentication and accounting. This is typically added by the
Access Point and uniquely identifies an SSID. This is useful when the SSID is
not available in the called-station-id (e.g., datatrigger scenarios). When this
attribute is configured for inclusion but no vlan is present in the UE payload,
the attribute will not be reflected in RADIUS.
Defines the initial lease-time used for data-triggered DHCP relay hosts. If this
attribute is not provided or equal to zero, the used lease-time will be 7 days.
This lease time will be overridden upon the first renew after data-triggered
host-creation.
Received Signal Strength Indication. Used in conjunction with the radius-
proxy track-accounting feature. When the radius-proxy receives this attribute
in an accounting message, it will be copied into the DHCP lease state and
echoed by the SROS accounting.
This is used to identify the host in a GTP-C connection. If not present and a
gtp-c connection is requested, the subscriber-id or username in the EAP-SIM
message will be parsed as an IMSI. This should be provided for any GTP-C
user.
Used to signal the QOS for default bearer or primary PDP context via GTP
"QOS IE" in create-PDP-context and "Bearer QOS" in create-session-request
7750 SR RADIUS Attributes Reference Guide
Description