Danfoss VLT 5000 FLUX Operating Instructions Manual page 157

...........................................................
Main Reactance
...............................................................
Mains failure
...............................................................
Mains failure
.................................................................
Mains fault
...........................................................
Mains Interference
..............................................................
Mains supply
..............................................
Mains supply (L1, L2, L3):
.........................................................
Max motor speed
...........................................................
Maximum Inertia
..................................................
Maximum reference
..........................................................
Mechanical brake
..................................................
Mechanical dimensions
...................................................
Mechanical installation
................................................................
Menu mode
...........................................................
Minimum Intertia
...................................................
Minimum reference
..............................................
Minor Interference on Mains
................................................................
Miscellaneous
..........................................................
Moment of inertia
...........................................................................
Motor
...............................................................
Motor cables
.........................................................
Motor connection
..........................................................
Motor current
..............................................................
Motor current
...........................................................
Motor frequency
.........................................................
Motor Parameters
................................................................
Motor power
........................................................
Motor Protection
......................................................
Motor shaft direction
................................................
Motor thermal protection
...............................................................
Motor voltage
............................................................
Multi-references
N
.......................................................
Nameplate data
.................................................
Normal-constant torque
Normal/high overload torque control
O
..........................................................
Operating hours,
..........................................................
Operating mode
..........................................................
Operation mode
.........................................................................
Output
..........................................
Output speed range/Direction
..............................................................
Output speed.
......................................................
Overvoltage control
P
..........................................................
proportional gain
.........................................................
Parameter groups
...................................................
Parameter setup keys:
MG.55.A6.02 - VLT is a registered Danfoss trademark
76
105
91
107
8
143
138
80
77
81, 81
85
14
17
48
76
80, 80
8
6
75
6
38
19
85, 86
63
70
75
69
9, 19
19
19
64
54
69, 70
69
..................................
59
116
118
118
5
80
80
103
106
48
45
®
VLT 5000 FLUX
..................................................................
Phase loss
.......................................................
Phase Loss Monitor
...........................................................................
PLC
...........................................................
Pole number
.................................................
Potentiometer reference
...................................................................
Power
........................................................
Power monitoring,
....................................................................
Power up
.....................................................................
Pre-heat
...........................................................
Pre-magnetizing
...........................................................
Preset reference
......................................................
Preset reference, on
...........................................
Programmable Signal Outputs
......................................................
Programming Setup
.......................................................
Pulse reference
............................................................
Pulse start/stop
Q
........................................................
Quick menu mode
...................................................
Quick Menu parameter
................................................
Quick menu, userdefined
...........................................
Quick Setup via Quick menu
..................................................................
Quick stop
......................................................
Quick-stop
R
..............................................................
ramp-up time.
..............................................................
Reference
.........................................................................
reset
......................................................................
Ramp 2
..................................................................
Ramp type
.................................................................
Ramp type,
.....................................................
Ramp-down time
.........................................................
Ramp-down time.
..............................................................
Ramp-up time
.......................................................
Rated motor speed
..........................................................................
RCD
.............................................................
Read-outstate
..............................................................
Reference
........................................................
Reference function
..........................................................
References
......................................................
Relay outputs:
....................................................................
Reset
..............................................................
Reversing
...................................................................
RFI switch
..............................................
Rotor Leakage Reactance
...........................................................
Rotor resistance
.......................................................................
RS 232
.......................................................................
RS 485
S
86
86
41
76, 76
37
63, 63
104
66
73
72
84
90
8
62
64, 91
36
47
48
66
48
82
89, 89, 110
82
63, 80
104
91
81
81
81, 81
82
81
70
22
47
63, 92
83
6, 83, 84
140, 140
89, 89
90, 111
42
76
75
35
34
157