IBM NeXtScale nx360 M4 Installation And Service Manual page 335

S.68005 [S.68005] An error has been detected by
the the IIO core logic on Bus %. The
Global Fatal Error Status register
contains %. The Global Non-Fatal Error
Status register contains %. Please check
error logs for the presence of additional
downstream device error data.
Explanation: Critical IOH-PCI Error
Severity: Error
User response: Complete the following steps:
1. Check log for a separate error for an associated
PCIe device and service that error.
2. Check IBM support site for an applicable service
bulletin or firmware update for the system or
adapter that applies to this error.
3. (Trained Service technician only) Replace the
system board.
S.680B8 [S.680B8] Internal QPI Link Failure
Detected.
Explanation: Internal QPI Link Failure Detected
Severity: Error
User response: Complete the following steps:
1. Check IBM support site for an applicable service
bulletin or firmware update that applies to this
error.
2. Inspect processor socket for foreign debris or
damage. If debris is found remove debris.
3. If error recurs, or socket damage is found, replace
the system board (Trained Service technician only) .
4. (Trained Service Technician Only) Replace the
processor.
S.680B9 [S.680B9] External QPI Link Failure
Detected.
Explanation: External QPI Link Failure Detected
Severity: Error
User response: Complete the following steps:
1. Check IBM support site for an applicable service
bulletin or firmware update that applies to this
error.
2. Inspect processor socket for foreign debris or
damage. If debris is found remove debris.
3. If error recurs, or socket damage is found, replace
the system board (Trained Service technician only) .
W.11004 [W.11004] A processor within the system
has failed the BIST.
Explanation: Processor Self Test Failure Detected
Severity: Error
User response: Complete the following steps:
1. If the Processor or firmware was just updated,
check IBM support site for an applicable service
bulletin or firmware update that applies to this
Processor error.
2. (Trained service technician only) If there are
multiple Processor's, swap Processor's to move
affected Processor to another Processor socket and
retry. If problem follows the affected Processor, or
this is a single Processor system, replace the
Processor. Inspect Processor socket on each
Processor removal and replace system board first if
damaged or mis-aligned pins are found.
3. (Trained Service technician only) Replace the
system board.
W.3048006 [W.3048006] UEFI has booted from the
backup flash bank due to an Automatic
Boot Recovery (ABR) event.
Explanation: Automated Boot Recovery, Booting
Backup UEFI Image
Severity: Warning
User response: Complete the following steps:
1. Check IBM support site for an applicable service
bulletin or firmware update that applies to this
error.
2. Reflash Primary UEFI image. Refer to UEFI
Recovery section of service information for this
product.
3. (Trained service technician only) Replace the
system board.
W.305000A [W.305000A] An invalid date and time
have been detected.
Explanation: RTC Date and Time Incorrect
Severity: Warning
User response: Complete the following steps:
1. Check IMM/chassis event log. This event should
immediately precede 0068002 error. Service that
event or any other battery related errors.
2. Use F1 Setup to reset date and time. If problem
returns after a system reset, replace CMOS battery.
3. If problem persists then check IBM support site for
an applicable service bulletin or firmware update
that applies to this error.
4. Trained Service technician only) Replace the system
board.
W.3058009 [W.3058009] DRIVER HEALTH
PROTOCOL: Missing Configuraiton.
Requires Change Settings From F1.
Explanation: DRIVER HEALTH PROTOCOL: Missing
Configuration. Requires Change Settings From F1
Appendix B. UEFI (POST) error codes
S.68005 • W.3058009
317