IBM NeXtScale nx360 M4 Installation And Service Manual page 246

806f000f-22010bff • 806f0013-1701ffff
Alert Category: Critical - Other
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0766
SNMP Trap ID: 50
Automatically notify Support: No
User response: This is a UEFI detected event. The
UEFI(POST) error for this event can be found in the
logged IMM message text. Please refer to the
UEFI(POST) error code in the "UEFI(POST) error code"
section of the Information Center for the appropriate
user response. Firmware Error : Sys Boot Status :
806f000f-22010bff Firmware BIOS (ROM) corruption
was detected on system
[ComputerSystemElementName] during
POST. (ABR Status)
Explanation: Firmware BIOS (ROM) corruption was
detected on the system during POST.
Severity: Info
Alert Category: Critical - Other
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0850
SNMP Trap ID: 40
Automatically notify Support: No
User response:
1. Make sure the server meets the minimum
configuration to start (see Power-supply LEDs).
2. Recover the server firmware from the backup page:
a. Restart the server. b. At the prompt, press F3 to
recover the firmware.
3. Update the server firmware to the latest level (see
Updating the firmware). Important: Some cluster
solutions require specific code levels or coordinated
code updates. If the device is part of a cluster
solution, verify that the latest level of code is
supported for the cluster solution before you update
the code.
4. Remove components one at a time, restarting the
server each time, to see if the problem goes away.
5. If the problem remains, (trained service technician)
replace the system board.
Firmware Error : Sys Boot Status :
806f000f-22010cff CPU voltage mismatch detected on
[ProcessorElementName]. (ABR Status)
Explanation: This message is for the use case when an
implementation has detected a CPU voltage mismatch
with the socket voltage.
Severity: Error
228
IBM NeXtScale nx360 M4 Type 5455: Installation and Service Guide
Alert Category: Critical - CPU
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0050
SNMP Trap ID: 40
Automatically notify Support: No
User response: This is a UEFI detected event. The
UEFI(POST) error code for this event can be found in
the logged IMM message text. Please refer to the
UEFI(POST) error code in the "UEFI(POST) error code"
section of the Info Center for the appropriate user
response. Firmware Error : Sys Boot Status :
806f000f-2201ffff The System
[ComputerSystemElementName]
encountered a POST Error. (ABR Status)
Explanation: This message is for the use case when an
implementation has detected a Post Error.
Severity: Error
Alert Category: Critical - Other
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0184
SNMP Trap ID: 50
Automatically notify Support: No
User response: This is a UEFI detected event. The
UEFI(POST) error code for this event can be found in
the logged IMM message text. Please refer to the
UEFI(POST) error code in the "UEFI(POST) error code"
section of the Information Center for the appropriate
user response. Firmware Error : Sys Boot Status :
806f0013-1701ffff A diagnostic interrupt has occurred
on system
[ComputerSystemElementName]. (NMI
State)
Explanation: This message is for the use case when an
implementation has detected a Front Panel NMI /
Diagnostic Interrupt.
Severity: Error
Alert Category: Critical - Other
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0222
SNMP Trap ID: 50
Automatically notify Support: No
User response: If the NMI button has not been
pressed, complete the following steps:
1. Make sure that the NMI button is not pressed.
2. Replace the operator information panel cable.
3. Replace the operator information panel.