Table Of Contents - Kyocera TASKalfa 3510i Service Manual

Table of Contents

Service Manual1
Revision History3
Safety Precautions5
Safety Warnings And Precautions6
Symbols6
Installation Precautions7
Precautions For Maintenance8
Miscellaneous Precautions9
Table Of Contents11
Nl/2P812
Machine Specifications15
Machine (Front Side)15
Printer Specifications18
Scanner Specifications19
Parts Names20
Machine (Front Side) Parts View20
Machine (Rear Side) Parts View22
Operation Panel Parts View23
Machine Cross Section View24
Installation Environment25
Installation Procedure26
Unpacking And Installation26
Unpacking27
Remove The Tapes And Spacer28
Install The Optional Paper Feeder (Option)29
Load Paper29
Install The Toner Container31
Switch The Cassette Heater Switch33
Precaution For Loading Paper33
Attaching The Language Label (Excluding 240V Ac Model)34
Install The Other Optional Devices35
Release The Scanner Lock35
Connect The Power Cord36
Installing Toner36
Execution Of Mentenance Item U95236
Exit Maintenance Mode37
Print Out A User Setting List37
Make Test Copies37
Setting Initial Copy Modes38
Factory Settings38
Option Composition39
Software Option40
Installing The Key Counter (Option)41
Installing Directly On The Device41
Supplied Parts Of Key Counter Set (302A369709)41
Key Counter Installation Procedure42
Mounting On The Document Table48
Supplied Parts Of Document Table (1902Lc0Un2)49
Installing The Gigabit Ethernet Board (Option)59
Installing The Ic Card Reader Holder (Option)61
Supplied Parts Of Ic Card Reader Holder (E) (1709Am0Un1)61
Enabling Ic Card Authentication71
Installing The Keyboard Holder (B) (Option)72
Supplied Parts Of Keyboard Holder (B) (1709Af0Un1)72
Installing The Printed Document Guard Kit (Option)80
Supplied Parts Of Printed Document Guard Kit80
When Dp Junction Pwb Is Not Used81
When Dp Junction Pwb Is Used83
Installing The Key Card Mk-2 (Option For Japan Only)86
Supplied Parts Of Document Tablet (1902H70Un2)86
Installing The Coin Vender (Option For Japan Only)97
Maintenance Mode101
Executing A Maintenance Item101
Maintenance Modes Item List102
U250 Checking/Clearing The Maintenance Cycle106
Contents Of The Maintenance Mode Items111
Event Log113
Detail Of Event Log114
Service Status Page (1)117
Service Status Page (2)118
Detail Of Service Status Page119
U001 Exiting The Maintenance Mode123
U002 Setting The Factory Default Data123
U003 Setting The Service Telephone Number124
U004 Setting The Machine Number124
U010 Setting The Maintenance Mode Id125
U018 Check Firmware Checksum126
U019 Displaying The Firrmware Version127
U021 Memory Initializing129
U024 Hdd Formatting130
U025 Firmware Update (Security)130
U026 Pulling Backup Data131
U030 Checking The Operation Of The Motors131
U031 Checking Switches And Sensors For Paper Conveying132
U032 Checking The Operation Of The Clutches133
U033 Checking The Operation Of The Solenoids133
U034 Adjusting The Print Start Timing134
U035 Setting The Printing Area For Folio Paper137
U037 Checking The Operation Of The Fan Motors137
U051 Adjusting The Deflection In The Paper138
U053 Setting The Adjustment Of The Motor Speed139
U061 Checking The Operation Of The Exposure Lamp140
U063 Adjusting The Shading Position140
U065 Adjusting The Scanner Magnification141
U066 Adjusting The Scanner Leading Edge Registration143
U067 Adjusting The Scanner Center Line144
U068 Adjusting The Scanning Position For Originals From The Dp145
U070 Adjusting The Dp Magnification146
U071 Adjusting The Dp Scanning Timing148
U072 Adjusting The Dp Center Line150
U073 Checking The Scanner Operation151
U074 Adjusting The Dp Input Light Luminosity152
U087 Setting Dp Reading Position Modification Operation153
U089 Outputting A Mip-Pg Pattern154
U091 Setting The White Line Correction155
U099 Adjusting Original Size Detection157
U100 Adjusting Main High Voltage159
U101 Adjust 1St Transfer Voltage Output161
U108 Setting Separation Shift Bias162
U110 Checking The Drum Count162
U111 Checking The Drum Drive Time163
U117 Checking The Drum Number163
U118 Displaying The Drum History164
U127 Checking/Clearing The Transfer Count164
U130 Initial Setting For The Developer165
U139 Displaying The Temperature And Humidity Outside The Machine165
U140 Setting Developer Bias166
U147 Setting For Toner Applying Operation167
U148 Setting Drum Refresh Mode167
U150 Checking Sensors For Toner168
U157 Checking The Developer Drive Time168
U158 Checking The Developer Count169
U161 Setting The Fuser Control Temperature169
U167 Checking The Fuser Count170
U198 Set Fuser Phase Control170
U199 Displaying Fuser Heater Temperature171
U200 Turning All Leds On171
U201 Initializing The Touch Panel172
U202 Setting The Kmas Host Monitoring System178
U203 Checking Dp Operation179
U204 Setting The Presence Or Absence Of A Key Card Or Key Counter180
U206 Setting The Presence Or Absence Of A Coin Vender181
U207 Checking The Operation Panel Keys184
U209 Set Rtc (Real Time Clock) Date184
U221 Setting The Usb Host Lock Function185
U222 Setting The Ic Card Type185
U223 Operation Panel Lock186
U224 Panel Sheet Extension187
U234 Setting Punch Destination188
U237 Setting Finisher Stack Quantity189
U240 Checking The Operation Of The Finisher190
U241 Checking The Operation Of The Switches Of The Finisher192
U243 Checking The Operation Of The Dp Motors194
U244 Checking The Dp Switches195
U245 Checking Messages196
U246 Setting The Finisher197
U247 Setting The Paper Feed Device201
U251 Checking/Clearing The Maintenance Counter203
U252 Setting The Destination204
U253 Switching Between Double And Single Counts205
U260 Selecting The Timing For Copy Counting206
U265 Setting Oem Purchaser Code206
U278 Setting The Delivery Date207
U285 Setting Service Status Page207
U326 Setting The Black Line Cleaning Indication208
U327 Setting The Cassette Heater Control209
U332 Setting The Size Conversion Factor209
U340 Setting The Applied Mode210
U341 Specific Paper Feed Location Setting For Printing Function211
U343 Switching Between Duplex/Simplex Copy Mode211
U345 Setting The Value For Maintenance Due Indication212
U346 Selecting Sleep Mode213
U402 Adjusting Margins Of Image Printing214
U403 Adjusting Margins For Scanning An Original On The Contact Glass215
U404 Adjusting Margins For Scanning An Original From The Dp216
U407 Adjusting The Leading Edge Registration For Memory Image Printing217
U410 Adjusting The Halftone Automatically218
U411 Adjusting The Scanner Automatically219
U415 Adjusting The Print Position Automatically226
U425 Setting The Target227
U470 Setting The Jpeg Compression Ratio232
U485 Setting The Image Processing Mode235
U600 Initializing All Data236
U601 Initializing Permanent Data237
U603 Setting User Data 1237
U604 Setting User Data 2238
U605 Clearing Data238
U610 Setting System 1239
U611 Setting System 2241
U612 Setting System 3242
U615 Setting System 6243
U620 Setting The Remote Switching Mode243
U625 Setting The Transmission System 1244
U630 Setting Communication Control 1245
U631 Setting Communication Control 2247
U632 Setting Communication Control 3248
U633 Setting Communication Control 4249
U634 Setting Communication Control 5250
U640 Setting Communication Time 1251
U641 Setting Communication Time 2252
U650 Setting Modem 1255
U651 Setting Modem 2256
U660 Setting The Ncu257
U670 Outputting Lists259
U671 Clear Fax Back Up Data260
U695 Fax Function Customize261
U698 Setting The Port Addressed In Maintenance Mode262
U699 Setting The Software Switches263
U901 Checking Copy Counts By Paper Feed Locations265
U903 Checking/Clearing The Paper Jam Counts266
U904 Checking/Clearing The Call For Service Counts267
U905 Checking Counts By Optional Devices268
U906 Resetting Partial Operation Control268
U908 Checking The Total Counter Value269
U910 Clearing The Print Coverage Data269
U911 Checking Copy Counts By Paper Sizes270
U917 Setting Backup Data Reading/Writing271
U920 Checking The Copy Counts273
U927 Clearing The All Copy Counts And Machine Life Counts (One Time Only)274
U928 Checking Machine Life Counts274
U930 Checking/Clearing The Charger Roller Count275
U933 Set Maintenance Mode Execute Log276
U935 Relay Board Maintenance277
U942 Setting Of Deflection For Feeding From Dp278
U952 Maintenance Mode Workflow279
U964 Checking Of Log281
U969 Checking Of Toner Area Code282
U977 Data Capture Mode282
U978 Clear Optional Function283
U984 Checking The Developer Unit Number283
U985 Displaying The Developer History284
U989 Hdd Scan Disk284
U991 Checking The Scanner Operation Count285
Paper Misfeed Detection287
Paper Misfeed Indication287
Paper Misfeed Detection Component289
Initial Jam290
Secondary Paper Feed Request Time Out290
No Paper Feed From Cassette290
Multiple Sheets In Cassette290
Feed Sensor 1 Non Arrival Jam291
Feed Sensor 1 Stay Jam291
Pf Feed Sensor 1 Stay Jam291
Pf Feed Sensor 2 Non Arrival Jam291
Registration Sensor Non Arrival Jam292
Eject Sensor Non Arrival Jam292
Eject Sensor Stay Jam292
Duplex Sensor Non Arrival Jam292
Bridge Conveying Sensor 1 Non Arrival Jam293
Bridge Conveying Sensor 1 Stay Jam293
Bridge Conveying Sensor 2 Non Arrival Jam293
Bridge Conveying Sensor 2 Stay Jam294
Df Paper Entry Error294
Df Front Cover Open294
Mb Cover Open294
Df Middle Eject Sensor Non Arrival Jam295
Df Middle Eject Sensor Stay Jam295
Df Tray Upper Surface Sensor Non Arrival Jam295
Df Eject Paper Sensor Stay Jam295
Df Side Registration Sensor 1 Stay Jam296
Df Side Registration Sensor 2 Stay Jam296
Df Staple Operation Error296
Mb Eject Sensor Stay Jam296
No Paper Feed From Dp297
Dp Original Conveying Jam297
Dp Paper Feed Sensor Stay Jam297
Dp Registration Sensor Non Arrival Jam297
Dp Cis Sensor Stay Jam298
Dp Eject Sensor Non Arrival Jam298
Dp Timing Sensor Stay Jam298
Dp Eject Sensor Stay Jam298
Self Diagnostic Codes299
0030 Fax Control Pwb System Error299
0100 Backup Memory Device Error299
0120 Mac Address Data Error300
0130 Backup Memory Read/Write Error (Main Pwb)300
0140 Backup Memory Data Error (Main Pwb)300
0150 Backup Memory Read/Write Error (Engine Pwb)300
0180 Machine Number Mismatch301
0350 Panel Pwb Communication Error301
0620 Fax Image Dimm Error301
0630 Dma Error302
0640 Hard Disk Error302
0650 Fax Image Dimm Check Error303
0660 Hard Disk Encryption Key Error303
0670 Hard Disk Overwriting Erasure Error303
0800 Image Processing Error - Jam010X Is Detected Twice304
0830 Fax Control Pwb Flash Pro Gram Area Checksum Error304
0840 Faults Of Rtc304
0870 Pcfax Control Pwb To Main Pwb High Capacity Data Transfer Error304
0920 Fax File System Error305
1010 Lift Motor 1 Error305
1020 Lift Motor 2 Error306
1030 Pf Lift Motor 1 Error (Paper Feeder)307
1040 Pf Lift Motor 2 Error (Paper Feeder)308
1100 Pf Lift Motor 1 Error (Large Capacity Feeder)309
1110 Pf Lift Motor 2 Error (Large Capacity Feeder)310
1800 Paper Feeder Communication Error311
1900 Paper Feeder Eeprom Error311
2000 Main Motor Steady-State Error312
2010 Main Motor Startup Error312
2500 Paper Feed Motor Steady-State Error313
2510 Paper Feed Motor Startup Error313
2600 Pf Drive Motor Error (Paper Feeder)314
2610 Pf Drive Motor Error (Large Capacity Feeder)314
3100 Scanner Carriage Error315
3210 Cis Lamp Error316
3220 Led Error316
3300 Optical System (Agc) Error317
3310 Cis Agc Error317
3500 Communication Error317
3600 Scanner Sequence Error318
3700 Scanner Device Error318
3900 Backup Memory Read/Write Error (Isc Pwb)318
4001 Polygon Motor Synchronization Error318
4011 Polygon Motor Steady-State Error319
4101 Bd Initialization Error319
4201 Bd Steady-State Error319
5101 Main High-Voltage Error320
6020 Abnormally High Fuser Thermistor 2 Temperature321
6030 Broken Fuser Thermistor 2 Wire321
6200 Broken Fuser Edge Heater Wire322
6220 Abnormally High Fuser Edge Thermistor Temperature322
6230 Broken Fuser Edge Thermistor Wire323
6250 Abnormally Low Fuser Edge323
6400 Zero-Cross Signal Error324
6910 Engine Software Ready Error324
7200 Broken Outer Temperature Sensor 2 Wire324
7210 Short-Circuited Outer Temperature Sensor325
7800 Broken Outer Temperature Sensor Wire325
7810 Short-Circuited External Thermistor Wire325
7901 Drum Eeprom Error326
7911 Developer Unit Eeprom Error326
8010 Punch Motor 1 Error327
8020 Punch Motor 2 Error328
8030 Punch Motor 3 Error329
8090 Df Paddle Motor Error330
8100 Df Eject Release Motor Error331
8110 Df Shift Motor 1 Error (3000-Sheet Finisher)332
8120 Df Shift Motor 2 Error (3000-Sheet Finisher)333
8130 Df Shift Release Motor Error (3000-Sheet Finisher)334
8140 Df Tray Error 1335
8150 Df Tray Error 2336
8160 Df Tray Error 3337
8170 Df Side Registration Motor 1 Error 1338
8180 Df Side Registration Motor 1 Error 2339
8190 Df Side Registration Motor 2 Error 1340
8200 Df Side Registration Motor 2 Error 2341
8210 Df Slide Motor Error342
8230 Df Staple Motor Error 1343
8240 Df Staple Motor Error 2343
8260 Df Middle Motor Error344
8410 Punch Slide Motor Error 1345
8420 Punch Slide Motor Error 2346
8430 Punch Unit Communication Error347
8500 Mailbox Communication Error347
8510 Mb Conveying Motor Error 1 (3000-Sheet Finisher)347
8520 Mb Conveying Motor Error 2 (3000-Sheet Finisher)348
8800 Document Finisher Main Program Error348
8900 Document Finisher Backup Error349
8990 Df Setup Error349
9000 Document Processor Communication Error349
9010 Coin Vender Communication Error350
9040 Dp Lift Motor Going Up Error350
9050 Dp Lift Motor Going Down Error351
9060 Dp Eeprom Error351
9070 Communication Error Between Dp And Shd351
9080 Led Fault Detection352
9100 Coin Vender Control Pwb Error352
9110 Coin Vender Rejector Error352
9120 Sensor Error In Coin Vender Change (Yen 10)352
9140 Sensor Error In Coin Vender Change (Yen 100)353
9160 Coin Vender Pay-Out Error353
9170 Coin Vender Pay-Out Sensor Error353
9500 Isc Pwb Error A353
9520 Isc Pwb Error C354
9940 Confidential Document Guard Uninstalled Error354
9950 Isc Pwb Error C354
F000 Communication Error Between Main Pwb And Operation Pwb354
F010 - F013 Main Pwb Checksum Error355
F020 - F023 System Memory Error, Controller Detection Error355
F040 Communication Error Between Main Pwb And Print Engine355
F050 Print Engine Rom Checksum Error355
F051 Scanner Engine Rom Checksum Error356
Image Formation Problems357
No Image Appears (Entirely White)357
No Image Appears (Entirely Black)358
Image Is Too Light359
The Background Is Colored359
White Streaks Are Printed Vertically359
Black Streaks Are Printed Vertically360
Streaks Are Printed Horizontally360
One Side Of The Print Image Is Darker Than The Other360
Spots Are Printed361
Image Is Blurred361
The Leading Edge Of The Image Is Consistently Misaligned With The Original361
The Leading Edge Of The Image Is Sporadically Misaligned With The Original361
Paper Is Wrinkled362
Offset Occurs362
Part Of Image Is Missing362
Fusing Is Loose362
Image Is Out Of Focus363
Image Center Does Not Align With The Original Center363
Electric Problems364
Mechanical Problems368
Send Error Code369
Scan To Smb Error Codes369
Scan To Ftp Error Codes370
Scan To E-Mail Error Codes372
Error Codes374
Table Of General Classificatio375
U004Xx Error Code Table: Interrupted Phase B378
U006Xx Error Code Table: Problems With The Unit379
U008Xx Error Code Table: Page Transmission Error379
U009Xx Error Code Table: Page Reception Error379
U010Xx Error Code Table: G3 Transmission380
U011Xx Error Code Table: G3 Reception382
U017Xx Error Code Table: V.34 Transmission383
U018Xx Error Code Table: V.34 Reception384
U023Xx Error Code Table: Relay Command Abnormal Reception384
U044Xx Error Code Table: Encrypted Transmission384
Precautions For Assembly And Disassembly385
Drum Unit385
Toner385
How To Tell A Genuine Kyocera Toner Container386
Outer Covers387
Detaching And Refitting The Front Cover387
Detaching And Refitting The Rear Cover389
Detaching And Refitting The Inner Tray390
Detaching And Refitting The Front Upper Cover391
Detaching And Refitting The Eject Rear Cover392
Paper Feed Section393
Detaching And Refitting The Primary Paper Feed Unit393
Detaching And Refitting The Mp Paper Feed Roller And Mp Separation Pad394
Detaching And Refitting The Registration Cleaner395
Detaching And Refitting The Mp Tray396
Developing Section397
Detaching And Refitting The Developing Unit397
Drum Section400
Detaching And Refitting The Drum Unit400
Detaching And Refitting The Chager Roller Unit400
Transfer/Separation Section401
Detaching And Refitting The Transfer Roller Unit401
Fuser Section402
Detaching And Refitting The Fuser Unit402
Drive Section403
Detaching And Refitting The Drive Unit 1403
Detaching And Refitting The Drive Unit 2404
Optical Section405
Detaching And Refitting The Laser Scanner Unit405
Detaching And Refitting The Image Scanner Unit406
Refitting The Isu408
Detaching And Refitting The Led Unit409
Detaching And Refitting The Scanner Wires411
Detaching The Scanner Wires411
Fitting The Scanner Wires419
Pwbs422
Detaching And Refitting The Main Pwb422
Remarks On Main Pwb Replacement425
Detaching Of Eeprom425
If The Main Pwb Was Replaced With A Service Supplied Part426
Procedures To Be Followed After The Eeprom On The Main Pwb Has Been Replaced426
Detaching And Refitting The Engine Pwb428
Remarks On Engine Pwb Replacement432
Detaching And Refitting The Power Source Pwb433
Detaching And Refitting The High Voltage Pwb434
Detaching And Refitting The Isc Pwb435
Detaching And Refitting The Operation Panel Pwb 1436
Detaching And Refitting The Language Sheet439
Others439
Detaching And Refitting The Conveying Unit440
Direction Of Installing The Principal Fan Motors442
Upgrading The Firmware444
Safe-Update444
Emergency-Update445
Paper Feed/Conveying Section446
Cassette Paper Feed Section446
Cassette Paper Feed Section Block Diagram447
Mp Tray Paper Feed Section448
Mp Tray Paper Feed Section Block Diagram448
Conveying Section449
Paper Conveying Section Block Diagram449
Drum Section Overview450
Drum Section Block Diagram451
Developing Section Overview452
Developing Section Block Diagram453
Optical Section Overview454
Image Scanner Section454
Scanner Unit Diagram454
Image Scanner Unit (Isu) Diagram454
Scanner Unit Block Diagram455
Laser Scanner Section456
Laser Scanner Unit (Lsu) Diagram456
Laser Scanner Unit Block Diagram456
Transfer/Separation Section Overview457
Transfer/Separation Section Block Diagram457
Fuser Section Overview458
Fuser Section Block Diagram459
Eject/Feedshift Section460
Eject/Feed Shift Section Block Diagram461
Duplex Conveying Section462
Duplex Conveying Section Block Diagram463
Electrical Parts Layout464
Pwbs Layout464
List Of Correspondences Of Pwb Names465
Switches And Sensors Layout466
Motors Layout468
Others Layout469
Main Pwb472
Main Pwb Silk-Screen Diagram472
Engine Pwb481
Engine Pwb Silk-Screen Diagram481
Isc Pwb493
Isc Pwb Silk-Screen Diagram493
Operation Panel Pwb Main498
Power Source Pwb503
Appendixes506
List Of Maintenance Parts506
Maintenance Kits507
Periodic Maintenance Procedures508
Repetitive Defects Gauge511
Firmware Environment Commands512
Using Frpo Commands For Reprogramming Firmware512
Frpo Parameters512
System Error (Fxxxx) Outline518
Chart Of Image Adjustment Procedures523
Wiring Diagram526
Installation Guidedp-770(B) / (Document Processor), Dp-772 / (Document Processor) Installation Guide532
B) / (Document Processor)532
Supplied Parts534
Procedure Of Installation536
Attach The Fixing Fitting (Dp-772)537
Install The Dp537
Install The Angle Control Fitting538
To Adjust Dp Open-Close Angle 30 Degrees538
Connect The Dp Signal Line (Dp-770(B) Only)539
Connect The Dp Signal Line (Dp-772 Only)541
Installing The Dp Relay Pwb543
Fasten The Original Mat546
Installing The Hinge Cover (Dp-772 Only)547
Adhere The Label548
Operation Check549
Checking The Angle Of Leading Edge553
Checking The Angle Of Trailing Edge556
Automatic Adjustment Using The Original For Adjustment559
Using A Dp Auto Adjustment Original560
Checking The Magnification562
Checking The Leading Edge Timing564
Checking The Center Line566
Dp-773 (Document Processor) Installation Guide568
Supplied Parts (Dp-773)570
Attaching The Seals (Dp-773)571
Install The Dp (Dp-773)571
Fasten The Original Mat (Dp-773)572
Connect The Signal Lines (Dp-773)572
Install The Angle Control Fitting (Dp-773)573
To Adjust Dp Open-Close Angle 30 Degrees (Dp-773)573
Adhere The Label (Dp-773)574
Operation Check (Dp-773)575
Checking The Angle Of Leading Edge (Dp-773)579
Checking The Angle Of Trailing Edge (Dp-773)582
Automatic Adjustment Using The Original For Adjustment (Dp-773)586
Using A Dp Auto Adjustment Original (Dp-773)587
Checking The Magnification (Dp-773)588
Checking The Leading Edge Timing (Dp-773)590
Checking The Center Line (Dp-773)592
Pf-791 (500 X 2 Paper Feeder) Installation Guide594
Supplied Parts (Pf-791)596
Procedure Of Installation (Pf-791)597
Setting Paper Size Plate (Pf-791)599
Adjusting The Leading Edge Timing (Pf-791)600
Adjusting The Center Line (Pf-791)601
Pf-810 (3000-Sheet Deck) Installation Guide602
Supplied Parts (Pf-810)604
Procedure Of Installation (Pf-810)605
Setting Paper Size Plate (Pf-810)609
Changing Paper Size (Metric Specifications Only) (Pf-810)609
Adjusting The Cursor Width (Pf-810)611
Adjusting The Leading Edge Timing (Pf-810)613
Adjusting The Center Line (Pf-810)614
Df-791 (3000-Sheet Finisher) Installation Guide615
Supplied Parts (Df-791)617
Installation Procedure (Df-791)618
If Pf-810 Is Installed619
If Pf-791 Is Installed619
Adjusting The Height (Df-791)623
Adjusting The Stapling Position (Df-791)628
Df-770(D) (1000-Sheet Finisher) Installation Guide630
Supplied Parts (Df-770(D))632
Procedure Of Installation (Df-770(D))633
Adjusting The Height Of The Document Finisher (Df-770(D))634
Installation With 30 And 35 Ppm Monochrome Machines (Df-770(D))635
Installation With 25/25 Ppm Full-Color Machine (Df-770(D))636
If Pf-810 Is Installed (Df-770(D))637
If Pf-791 Is Installed (Df-770(D))637
Adjusting The Height (Df-770(D))642
Adjusting The Stapling Position (Df-770(D))646
Ak-740 (Bridge Unit) Installation Guide648
Ak-740 Attachment Kit For Black & White Mfp 30Ppm,35Ppm Color Mfp 25/25Ppm649
Mt-730(B) (Mailbox) Installation Guide650
Supplied Parts (Mt-730(B))653
Installation Procedure (Mt-730(B))654
Ph-7A/C/D (Punch Unit) Installation Guide665
Supplied Parts (Ph-7A/C/D)667
Installation Procedure (Ph-7A/C/D)668
Removing The Cover (Df-790)669
Edging673
Installing The Punch Pwb And Waste Hole Punch Box (Df-770)674
Band674
Installing The Punch Pwb And Waste Hole Punch Box (Df-790)678
Adjusting The Hole Punch Position (Ph-7A/C/D)682
Adjusting The Hole Punch Entry Registration (Ph-7A/C/D)682
Adjusting The Hole Punch Position Feed (Ph-7A/C/D)683
Centering The Hole Punch Position (Ph-7A/C/D)684
Dt-730(B) (Document Tray) Installation Guide686
Supplied Parts (Dt-730(B))689
Installation Procedure (Dt-730(B))691
Removing The Slot Cover (Dt-730(B))692
Install The Fax Circuit Board (Dt-730(B))693
Connect The Mfp To The Telephone Line (Dt-730(B))694
Connect The Mfp To The Separate Phone (Except For New Zealand Model) (Dt-730(B))695
Seal The Terminal (For New Zealand Model) (Dt-730(B))696
Wiring The Modular Connector Cable (High-Speed Mfps Only)696
Attach The Alphabet Labels (Excluding 100 V Models) (Dt-730(B))697
Attach The Ptt Label (For China, 110 V Models Only)700
Attach The Approval Label (For Australian/New Zealand Model Only)700
Initialize The Fax Circuit Board (Dt-730(B))701
When Installing The Multiport On A Machine (A) Which Has The 'Home' Key In The Operation Panel702
Removing The Slot Cover704
Install The Fax Circuit Board705
Seal The Terminal706
Connect The Mfp To The Telephone Line707
Wiring The Modular Connector Cable (High-Speed Mfps Only) (Dt-730(B))708
Initialize The Fax Circuit Board709
When Installing The Fax System On A Machine (B) Which Has The 'Accessibility Display' Key In The Operation Panel710
Installing The Memory Dimm712
Attach The Alphabet Labels (Excluding 100 V Models)718
When Installing The Multiport On A Machine (B) Which Has The 'Accessibility Display' Key In The Operation Panel723
Installation Guide For Black & White Mfp 30Ppm, 35Ppm/For Color Mfp 25/25Ppm730
Fax System (W) B Installation Guide732