Sm-Keypad Plus; Menu 40 Parameter Descriptions; Menu 41 Parameter Descriptions - Emerson unidrive sp User Manual

Parameter Keypad and
Parameter x.00
structure display
Holding the Up or Down key in the first method will cause the
parameters value to change more rapidly the longer the key is held, until
such time that the parameters maximum or minimum is reached.
However with the second method an increasing rate of change does not
take place when adjusting any other digit other than the least significant
digit since a digit can only have one of 10 different values. Holding the
Up or Down will cause an auto repeat and roll over to more significant
digits but the rate of change is unaltered. If the maximum or minimum is
exceeded when adjusting any other digit than the least significant one,
the maximum value will flash on the display to warn the user that the
maximum or minimum has been reached. If the user releases the Up or
Down key before the flashing stops the last in range value will re-appear
on the display. If the Up or Down key is held the display will stop flashing
after three seconds and the maximum value will be written to the
parameter.
Table 2-1 Menu 40 parameter descriptions
Parameter
40.00 Parameter 0
40.01 Language selection
40.02 Software version
40.03 Save to flash
40.04 LCD contrast
Drive and attribute database upload was
40.05
bypassed
40.06 Browsing favourites control
40.07 Keypad security code
40.08 Communication channel selection
40.09 Hardware key code
40.10 Drive node ID (Address)
40.11 Flash ROM memory size
40.19 String database version number
40.20 Screen saver strings and enable
40.21 Screen saver interval
40.22 Turbo browse time interval
Table 2-2 Menu 41 parameter descriptions
Parameter
41.00 Parameter 0
41.01
to Browsing filter source F01 to F50
41.50
41.51 Browsing favourites control
RW Read / Write
Bit Bit parameter
NC Not copied
PS Power down save
For more information about the SM-Keypad Plus, see the SM-Keypad Plus User Guide.
12
Parameter Advanced parameter
description format descriptions
Range( )
0 to 32767
English (0), Custom (1),
French (2), German (3),
Spanish (4), Italian (5)
999999
Idle (0), Save (1), Restore (2),
Default (3)
0 to 31
Updated (0), Bypass (1)
Normal (0), Filter (1)
0 to 999
Disable (0), Slot1 (1), Slot2 (2),
Slot3 (3), Slave (4), Direct (5)
0 to 999
0 to 255
4Mbit (0), 8Mbit (1)
0 to 999999
None (0), Default (1), User (2)
0 to 600
0 to 200ms
Range( )
0 to 32767
Pr 0.00 to Pr 391.51
Normal (0), Filter (1)
RO Read only
Txt Text string
RA Rating dependent
www.controltechniques.com
Serial comms
Macros
protocol
Parameters can be set to 0 by pressing the Up and Down keys
simultaneously.
2.6

SM-Keypad Plus

All SM-Keypad Plus displays built after data code N10 have software
version 4.02.00 programmed and support 5 languages (English, French,
German, Spanish and Italian) in addition to a user defined parameter set.
This software also gives the user access to two menus for SM-Keypad
Plus. Menu 40 is for SM-Keypad Plus set up, menu 41 selects commonly
used parameters for quick browsing.
Keypads built prior to N10 only support one user defined extra
parameter set only.
The SM-Keypad Plus contains two menus, menu 40 and menu 41. The
parameters in these menus are listed below.
Default( )
0
English (0)
Idle (0)
16
Normal (0)
0
Disable (0)
0
1
Default (1)
120
50ms
Default( )
0
0
Normal (0)
Uni Unipolar
FI Filtered
PT Protected
Electronic
Performance RFC mode
nameplate
Type
RW Uni
RW Txt
RO Uni
RW Txt
RW Uni
RO Txt
RW Txt
RW Uni
RW Txt
RW Uni
RW Uni
RO Txt
RO Uni
RW Txt
RW Uni
RW Uni
Type
RW Uni
RW Uni
RW Txt
Bi Bi-polar
DE Destination
US User save
Unidrive SP Advanced User Guide
Issue Number: 10
US
PT
US
PT
US
US
US
US
PT US
PT
US
US
US