Sharp AR-FX12 Service Manual page 36

66-42
Purpose
Function (Content) Used to rewrite the program to the PIC installed
in the FAX box.
Section FAX
Item
Operation/Procedure During writing, "EXECUTING" is displayed.
When writing is completed, if the process is OK,
"OK" is displayed. In case of an error, "NG" is
displayed. Possible causes of NG are:
•Write protect is set.
•PIC is not installed.
•Failure in access to PIC
Note: Release write protect.
SIMULATION 66-42
PIC PROGRAM RELOAD.
ARE YOU SURE?.
1. YES
2. NO
Press [START] key.
SIMULATION 66-42
PIC PROGRAM RELOAD EXECUTING...
After completion of reload
SIMULATION 66-42
PIC PROGRAM RELOAD
OK
<List of display values>
1 Execution (FAX program writing is allowed.)
2 Cancel (FAX program writing is allowed.)
* FAX program writing is allowed by the jumper and the DIP switch
which differ depending on the model.
66-43
Purpose
Function (Content) To execute this simulation, FAX program writing
must be allowed. (Jumper and DIP switch which
differ depending on the model)The adjustment
value of PIC are changed and written. The
current setting is highlighted beside the item.
Section FAX
Item
Operation/Procedure 1) Set the adjustment value with 10-key.
Press P key to save the entered value.
The setting range differs depending on the
item.
Example:1.Number of sensing until
settlement of the CI signal level:
(Default) 2, (Range) 1 - 15
* When the value outside the specified range is
displayed, scan from the PIC may not have
been completed. (Because of FAX program
write protection, etc.)
2) When YES is selected, the adjustment values
are collectively written into the PIC installed
to the FAX box.
Normal completion of writing: "WRITING OK"
In case of an error:"NG"
1
Press [CUSTOM SETTING] key.
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-24
SIMULATION 66-43
PIC ADJUSTMENT VALUE WRITING .
ENABLE WRITE PIN (for FAX PROGRAM ROM).
SELECT 0-12, AND PRESS START.
0. WRITING for PIC 1. ci_level_judge
2. ci_cycle_min 10 3. ci_cycle_max
5. ci_count 3 6. ci_detect
8. fnet_range 3 9. fnet_time_out
11. poff_time 3 12. mswon_level_judge
Serect other than 0,
Press [START] key or
and Press [START] key.
Press [CUSTOM SETTING] key
SIMULATION 66-43
PIC ADJUSTMENT VALUE WRITING. INPUT VALUE 1-15, AND
PRESS START.
1. ci_level_judge(1-15)
Serect 0,and
Press [START] key.
SIMULATION 66-43
PIC ADJUSTMENT VALUE WRITING.
ARE YOU SURE?
1.YES
2.NO
Press 1 key.
SIMULATION 66-43
PIC ADJUSTMENT VALUE WRITING.
EXECUTING...
SIMULATION 66-43
PIC ADJUSTMENT VALUE WRITING.
OK ( or NG )
<List of display values>
0 WRITING to PIC • • Writing to PIC
1 ci_level_judge(1-15)
2 ci_cycle_min(0-254)
3 ci_cycle_max(0-254)
4 ci_range(0-127)
5 ci_count(1-15)
6 ci_detect(1-15)
7 fnet_level_judge(1-15)
8 fnet_range(0-74)
9 fnet_time_out(76-255)
10 fnet_count(1-15)
11 poff_time(0-15)
12 mswon_level_judge(2-15)
2
107
4. ci_range 5 1
1
8 7. fnet_level_judge
3
100 10. fnet_count
3
2
Press [CUSTOM SETTING] key or
Press 2key
1
Press [CUSTOM SETTING] key