Sharp AR-FX12 Service Manual page 28

66-9
Purpose Operation test, check
Function (Content) Used to check the output operation of the FAX
sound signals.
(Sound output IC operation check)
(Only when FAX is installed.)
Section FAX
Item Operation
Operation/Procedure A voice message is outputted.
(Send level is set with SW.)
Enter a number during execution to change the
kind of signal.
Press START to start sending a voice message.
Press CUSTOM SETTINGS to terminate.
SIMULATION 66-9
MESSAGE OUTPUT CHECK.(SOFT SW.) SELECT 1-20, AND PRESS
START.
1.NONE 2.PAUSE
4.MESSAGE2 5.MESSAGE3
7.MESSAGE5 8.MESSAGE6
10.MESSAGE8 11.MESSAGE9
13.MESSAGE11 14.MESSAGE12
16.MESSAGE14 17.MESSAGE15
19.RINGER 20.EXT.TEL.RINGER
Select 1 and press [START] key.
SIMULATION 66-9
MESSAGE OUTPUT CHECK.(SOFT SW.) SELECT 1-20, AND PRESS
START.EXECUTING...
1.NONE 2.PAUSE
4.MESSAGE2 5.MESSAGE3
Same
display 7.MESSAGE5 8.MESSAGE6
10.MESSAGE8 11.MESSAGE9
13.MESSAGE11 14.MESSAGE12
16.MESSAGE14 17.MESSAGE15
19.RINGER 20.EXT.TEL.RINGER
Select 2 and press [START] key.
SIMULATION 66-9
MESSAGE OUTPUT CHECK.(SOFT SW.) SELECT 1-20, AND PRESS
START.EXECUTING...
1.NONE 2.PAUSE
4.MESSAGE2 5.MESSAGE3
7.MESSAGE5 8.MESSAGE6
10.MESSAGE8 11.MESSAGE9
13.MESSAGE11 14.MESSAGE12
16.MESSAGE14 17.MESSAGE15
19.RINGER 20.EXT.TEL.RINGER
2
3.MESSAGE1
6.MESSAGE4
9.MESSAGE7
12.MESSAGE10
15.MESSAGE13
18.ALARM
Press [CUSTOM SETTINGS] key.
1
3.MESSAGE1
6.MESSAGE4
9.MESSAGE7
12.MESSAGE10
15.MESSAGE13
18.ALARM
2
3.MESSAGE1
6.MESSAGE4
9.MESSAGE7
12.MESSAGE10
15.MESSAGE13
18.ALARM
Press [CUSTOM SETTINGS] key.
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-16
<List of set values>
1 NONE
2 PAUSE
3 MESSAGE1
4 MESSAGE2
5 MESSAGE3
6 MESSAGE4
7 MESSAGE5
8 MESSAGE6
9 MESSAGE7
10 MESSAGE8
11 MESSAGE9
12 MESSAGE10
13 MESSAGE11
14 MESSAGE12
15 MESSAGE13
16 MESSAGE14
17 MESSAGE15
18 ALARM
19 RINGER
20 EXT.TEL.RINGER
66-10
Purpose User data output, check (display, print)
Function (Content) Used to clear all data of image memory
(memory send, receive). Confidential data are
also cleared. (Only when FAX is installed.)
Section FAX
Item Data
Operation/Procedure The FAX image memory is cleared.
1) Select an item with 10 digit key pad and press
START. The following is executed and the
display returns to the initial state.
Only the Flash ROM area is cleared.
2) After completion of memory clear, reset.
SIMULATION 66-10
IMAGE MEMORY CLEAR.
ARE YOU SURE ?
1. YES
2. NO
Press [START] key and start clear.
SIMULATION 66-10
IMAGE MEMORY CLEAR. EXECUTING...
++++++
During execution of image memory clear, "+" is displayed.
When one block or a certain unit of area is cleared, "+" is added.
NONE
PAUSE
MESSAGE1
MESSAGE2
MESSAGE3
MESSAGE4
MESSAGE5
MESSAGE6
MESSAGE7
MESSAGE8
MESSAGE9
MESSAGE10
MESSAGE11
MESSAGE12
MESSAGE13
MESSAGE14
MESSAGE15
ALARM
RINGER
EXT.TEL.RINGER
1: Image memory clear 2: Not clear
1
1