Sharp AR-FX12 Service Manual page 24

66-2
Purpose Data clear
Function (Content) Used to set the FAX soft switch setup to the
default. (Except for the adjustment values)
Section FAX
Item Data
Operation/Procedure The current set value of SW1 is displayed.
Entry of 1 ~ 8 is effective.
1) Specify the bit to be changed (highlighted)
with a number.
2) Select the country code, and press START to
rewrite the setting.
For the country code, refer to the table below.
An entry other than the specified codes is
accepted as Japan.
* Conforms to Recommendations T.35.
3) Select a number with 10 digit key pad and
press START key to execute.
4) The soft switch (excluding the FAX adjustment
value) corresponding to the selected country
code is cleared.
1: FAX soft SW clear
2: Not clear
5) The selected country is highlighted.
SIMULATION 66-2
FAX SOFT SW.CLEAR (WIHTOUT ADJUSTMENT VALUE).
INPUT COUNTRY CODE, AND PRESS START.
Press [START] key.
SIMULATION 66-2
FAX SOFT SW. CLEAR.
ARE YOU SURE?
JAPAN
1:YES
2:NO
<Country codes>
U.S.A 1 0
* Conforms to Advisory Document T.35.
1 2 3 4 5 6 7 8
00000000
1
1 1 0 1 0
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-12
66-3
Purpose
Function (Content)
Section
Item
Operation/Procedure Select an item and press START key to execute.
SIMULATION 66-3
FAX PWB MEMORY CHECK. INPUT 1-13, AND PRESS START.
1. All Memory Device Check (once)
2. MFP SRAM (once)
4. MFP FLASH + OP FLASH (once)
5. MFP FLASH + OP FLASH (repeat)
6. MODEM EEPROM (once)
8. MODEM SRAM(G/A) (once)
10. MODEM SDRAM1 (once)
12. MODEM SDRAM2 (once)
Press [START] key.
In repeat, the number of repeat is displayed in
a four-digit decimal number as "CHECKING 0001."
When 9999 is exceeded, the number returns to 0000.
(A space is placed between CHECKING and the number.)
SIMULATION 66-3
FAX PWB MEMORY CHECK.
MFP SRAM: CHECKING
MFP FLASH: NO CHECK
NO CHECK
MODEM EEPROM: NG:A0010000
MODEM SDRAM2(G/A):NO CHECK
MODEM CASRAM: NG A11
1
MODEM SDRAM1: OK
When Check is "once," the display stops at the report display.
When [CUSTM SETTING] key pressed, the display returns to
the selection menu of 1 ~ 13.
<List of display values>
NO CHECK
CHECKING
OK
NG
<Items>
MFP SRAM (MFP control PWB)
MFP FLASH (FAX I/F PWB)
MFP OP.FLASH (FAX I/F PWB)
MODEM EEPROM (FAX PWB)
MODEM SRAM(G/A) (FAX PWB)
MODEM SDRAM1 (FAX PWB)
MODEM SDRAM 2(FAX PWB)
Operation test, check
Used to check the operations of FAX PWB
memory (read/write).
(This adjustment is required when replacing the
PWB with a new one.)
FAX
Data
The display goes to the next menu.
When "1. All Memory Device Check" is selected,
all memory devices are checked only once.
The error occurring address or the data line is
displayed for each item.
When an item with "repeat" is selected, the
result is displayed as "NG" or execution is
continued until [CUSTOM SETTINGS]) or ([CA]
key) is pressed.
3. MFP SRAM (repeat)
7. MODEM EEPROM (repeat)
9. MODEM SRAM(G/A) (repeat)
11. MODEM SDRAM1 (repeat)
13. MODEM SDRAM2 (repeat)
Press [CUSTOM SETTINGS] key.
The selected number is displayed.
When check is "repeat" and
[CUSTOM SETTINGS] key is pressed.
Not checked
Checking
Check complete OK
Check error
SRAM
FLASH Memory
FLASH Memory (AR-MM9)
1
1