Changing Med Attributes; Changing The Local_Preference Attribute - Dell S6000–ON Configuration Manual

To view BGP routes matching a certain community number or a pre-defined BGP community, use the
show ip bgp community command in EXEC Privilege mode.
Dell>show ip bgp community
BGP table version is 3762622, local router ID is 10.114.8.48
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal
Origin codes: i - IGP, e - EGP, ? - incomplete
Network
* i 3.0.0.0/8
*>i 4.2.49.12/30
* i 4.21.132.0/23
*>i 4.24.118.16/30 195.171.0.16
*>i 4.24.145.0/30
*>i 4.24.187.12/30 195.171.0.16
*>i 4.24.202.0/30
*>i 4.25.88.0/30
*>i 6.1.0.0/16
*>i 6.2.0.0/22
*>i 6.3.0.0/18
*>i 6.4.0.0/16
*>i 6.5.0.0/19
*>i 6.8.0.0/20
*>i 6.9.0.0/20
*>i 6.10.0.0/15
*>i 6.14.0.0/15
*>i 6.133.0.0/21
*>i 6.151.0.0/16
--More--

Changing MED Attributes

By default, Dell Networking OS uses the MULTI_EXIT_DISC or MED attribute when comparing EBGP
paths from the same AS.
To change how the MED attribute is used, enter any or all of the following commands.
• Enable MED comparison in the paths from neighbors with different ASs.
CONFIG-ROUTER-BGP mode
bgp always-compare-med
By default, this comparison is not performed.
• Change the bestpath MED selection.
CONFIG-ROUTER-BGP mode
bgp bestpath med {confed | missing-as-best}
– confed: Chooses the bestpath MED comparison of paths learned from BGP confederations.
– missing-as-best: Treat a path missing an MED as the most preferred one.
To view the nondefault values, use the show config command in CONFIGURATION ROUTER BGP
mode.

Changing the LOCAL_PREFERENCE Attribute

In Dell Networking OS, you can change the value of the LOCAL_PREFERENCE attribute.
To change the default values of this attribute for all routes received by the router, use the following
command.
198
Next Hop Metric
195.171.0.16
195.171.0.16
195.171.0.16
195.171.0.16
195.171.0.16
195.171.0.16
195.171.0.16
195.171.0.16
195.171.0.16
195.171.0.16
195.171.0.16
195.171.0.16
195.171.0.16
195.171.0.16
205.171.0.16
205.171.0.16
205.171.0.16
LocPrf Weight Path
100 0 209 701 80 i
100 0 209 i
100 0 209 6461 16422 i
100 0 209 i
100 0 209 i
100 0 209 i
100 0 209 i
100 0 209 3561 3908 i
100 0 209 7170 1455 i
100 0 209 7170 1455 i
100 0 209 7170 1455 i
100 0 209 7170 1455 i
100 0 209 7170 1455 i
100 0 209 7170 1455 i
100 0 209 7170 1455 i
100 0 209 7170 1455 i
100 0 209 7170 1455 i
100 0 209 7170 1455 i
100 0 209 7170 1455 i
Border Gateway Protocol IPv4 (BGPv4)