Table of Contents
Advertisement
Command
Write input name (per plane)
Read input name
Write output name (per plane)
Read output name
•
If a preset (global or plane) is unassigned, its name is displayed [unassigned].
NOTES:
•
If a global preset is saved but not named, its default name is Preset
•
If a plane preset is saved but not named, its default name is Pln
•
If you attempt to name or recall a preset that is not saved, or is unassigned, the unit responds with the error
message E11.
•
Putting a space in the name field sets the I/O and presets (global & plane) back to default.
Reset to Factory Defaults (Zap Commands)
Reset global presets and names
Reset individual global presets
Reset individual plane presets
Reset All RGB Delay to 0
seconds
Reset RGB Delay entire plane
Reset all audio gains to 0 dB
Reset audio gains to 0 dB for
entire plane
Reset all audio volume to 100%
Reset all audio volume to 100%
for entire plane
Unmute RGB/Audio (all mutes)
Unmute RGB/Audio (per plane)
Reset switcher
Reset flash memory
Absolute system reset
Reset all device settings and
delete files
E
ZY reset excludes IP settings (IP address, subnet mask, gateway address, unit name, DHCP settings and
NOTE:
port mapping [Telnet, web, or direct access]) in order to preserve communications with the device. This reset is
recommended after a firmware update.
X!
NOTES:
= Input number
X#
= Output number
X1!
= Global or plane preset
X2@
= Plane address
ASCII Command
Response
(Host to Switcher)
(Switcher to Host)
EX2@
X!
}
X2@
*
,nameNI
EX2@
X!
}
*
NI
name
EX2@
X#
}
X2@
*
,nameNO
EX2@
X#
}
*
NO
name
E
}
ZG
Zpg
E X1!
}
ZG
Zpg
E X2@
X1!
}
X2@
*
ZG
E
}
ZD
Zpd
E X2@
}
X2@
ZD
E
}
ZA
Zpa
E X2@
}
X2@
ZA
E
}
ZV
Zpv
E X2@
}
X2@
ZV
E
}
ZZ
Zpz
E X2@
}
X2@
ZZ
E
}
ZXXX
Zpx
E
}
ZFFF
Zpf
E
}
ZQQQ
Zpq
E
}
ZY
Zpy
01 - <maximum number of inputs>
01 - <maximum number of outputs>
1 - 32 = global
1 - 10 = plane
00 - 15 = 16 planes
90 - 99 = virtual planes (10 planes)
SMX System MultiMatrix Switcher • SIS Configuration and Control
Additional Description
X!
]
Nmi
,name
Assign a name to input
]
X#
]
Nmo
,name
Assign a name to output
]
X1!
.
X2@•
X1!
Pre
.
]
Clear all global presets and their
names.
X1!]
Clear global preset
X1!]
Clear plane preset
Zpg
]
Reset RGB Delay to zero.
]
Reset RGB Delay to zero.
Zpd
]
Reset all audio gains to zero.
]
Reset all audio gains to zero.
Zpa
]
Reset all volume to 100%.
]
Reset all volume to 100%.
Zpv
]
]
Zpz
]
Clear all ties and presets and reset
the SMX to factory defaults.
]
Reset flash memory (reset
user-supplied files).
]
Reset IP address to
192.168.254.254 and subnet mask
to 255.255.0.0.
]
Reset device and delete all files.
X!
.
X#
.
X1!
.
X1!
.
51
Advertisement
Table of Contents
