Table of Contents
Advertisement
NOTES:
•
The boards are hot-swappable: they can be installed or removed without
turning off or disconnecting the power. However, turning the power off prior
to installing or removing boards is recommended.
•
Use ESD precautions when installing a board to avoid damaging it. Keep the
board in the anti-static bag until needed. Use proper grounding techniques
during installation.
Frames and I/O Boards
See
Installing New Boards into an Empty SMX Frame
1.
Remove as many of the blanks plates from the rear of the unit as needed.
2.
When ready, remove the board from the anti-static bag, taking care not to touch any
of the components on the board. Slide the board into the open rear slot (see
carefully aligning it with the plastic slides in the frame. Push the board firmly into place.
PLA
NE
4
IN
ER
UT
MP
CO
3
8
2
7
S- VI
16
1
6
15
TE
MO
RE
14
5
13
22
S4
PLA
23
2/R
12
RS
16
11
15
10
14
Y
9
13
TS
12
IN PU
O
VI DE
11
4
C
10
PLA
NE
ITA
DIG
9
3
PLA
NE
8
2
7
TS
IN PU
6
5
1
TS
4
I IN
PU
HD
SD
3
I /
US
SD
®
T
2
ED
IDE
17T
O
LIST
IO/V
TUS
AUD
ARA
1
APP
X.
MA
V
1.3A
-240
50-6
0Hz
100
Figure 4.
SMX Frame Rear Showing Board Installation
3.
Tighten down the screws on each end of the board.
NOTE:
Use a tool to fully tighten the screws after initial installation and subsequent
removal and replacement of the boards.
4.
Repeat steps 1 through 3 for all boards needing installation.
NOTE:
If the unit is connected via RS-232 or RS-422, it responds with
when a board is installed or replaced.
The SMX is now ready for cabling (see
Replacing an Existing I/O Board
1.
Remove any input and output cables for the I/O board being replaced.
2.
Loosen the outer screws on the existing board and remove it from the unit.
3.
Slide the replacement board firmly into place and tighten down the screws.
4.
Repeat for all boards to be replaced. Any new boards are now ready for cabling.
To configure the SMX with the new cards, see
configuration methods for the SMX, see
Control Software
on page 59, and
on page 124 for a full list of available boards for the SMX.
4
T
OU
UT
ER
MP
CO
3
8
Y
2
7
16
1
6
15
5
14
C
13
12
16
SS
11
AD
RE
15
10
14
9
13
Y
S
UT
12
OU
TP
O
VI DE
D EO
11
10
4
9
C
3
8
RE
SS
AD
NE
7
2
S
UT
6
TP
OU
5
S
TP
UT
1
4
I OU
SD
I /
HD
3
SD
2
RE
SS
1
AD
EO
L VID
SS
AD
RE
O
R
8
U
L
T
7
R
P
L
U
6
R
R
T
L
L
16
S
R
R
5
15
L
L
4
R
R
L
14
R
L
3
13
R
L
L
2
R
R
L
12
L
1
R
R
L
L
11
O
10
R
U
L
T
R
P
9
L
U
T
S
R
I
8
N
L
7
R
P
RE
SS
L
U
NE
AD
T
PLA
6
R
R
L
L
16
S
R
5
15
R
Optional
L
L
4
R
R
L
14
L
3
R
R
L
L
13
R
2
12
R
L
L
1
R
R
L
11
L
I
10
R
Board
N
L
R
P
9
U
L
T
S
(audio shown)
Input/Output Boards
Operation
SIS Configuration and Control
HTML Configuration and Control
SMX MD System MultiMatrix Switcher • Installation
figure
Reconfig
on page 8 for details).
on page 13. For alternative
on page 34,
on page 87.
4),
SMX
11
Advertisement
Table of Contents
