Extron electronics DTP CrossPoint 4K Series Setup Manual
  1. Manuals
  2. Brands
  3. Extron electronics Manuals
  4. Matrix Switcher
  5. DTP CrossPoint 4K Series
  6. Setup manual

Extron electronics DTP CrossPoint 4K Series Setup Manual

Scaling presentation
Hide thumbs Also See for DTP CrossPoint 4K Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
Setup Guide
Matrix Switcher
DTP CrossPoint 4K Series
Scaling Presentation Matrix Switcher
68-2368-50 Rev. B
01 16

Advertisement

Table of Contents
loading

Related Manuals for Extron electronics DTP CrossPoint 4K Series

Summary of Contents for Extron electronics DTP CrossPoint 4K Series

  • Page 1 Setup Guide Matrix Switcher DTP CrossPoint 4K Series Scaling Presentation Matrix Switcher 68-2368-50 Rev. B 01 16...

  • Page 2: Safety Instructions

    Safety Instructions Safety Instructions • English Инструкция по технике безопасности • Русский WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated dangerous voltage ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан within the product’s enclosure that may present a risk of electric на...
  • Page 3 FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 4 Conventions Used in this Guide Notiications ATTENTION: • Risk of property damage. • Risque de dommages matériels. NOTE: A note draws attention to important information. TIP: A tip provides a suggestion to make working with the application easier. Software Commands Commands are written in the fonts shown here: ^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C [01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]...
  • Page 5 Trademarks All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks, registered service marks, and trademarks are the property of RGB Systems, Inc. or Extron Electronics: Registered Trademarks (®) AVTrac, Cable Cubby, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS,...

  • Page 7: Table Of Contents

    Setting the Front Panel Locks (Executive Modes) ..... 20 Selecting Lock Mode 2 or Toggling between Mode 2 and Mode 0 ......21 Selecting Lock Mode 2 or Toggling between Mode 2 and Mode 1 ......21 DTP CrossPoint 4K Series • Contents...
  • Page 8 DTP CrossPoint 4K Series • Contents...

  • Page 9: Introduction

    About this Guide NOTE: For more information on subjects in this guide, see the DTP CrossPoint 4K Series User Guide and the IPCP Pro Series User Guide, at www.extron.com. This guide provides instructions for an experienced installer to set up and operate the Extron DTP CrossPoint 4K Series matrix switchers.

  • Page 10: About The Dtp Crosspoint 4K Series

    About the DTP CrossPoint 4K Series The matrix switchers distribute HDCP-compliant HDMI and Extron proprietary DTP video and audio signal types (see igure 1). A matrix switcher routes any input signal to any combination of outputs. It can route multiple input and output conigurations simultaneously.

  • Page 11: Dtp Input And Output Signals

    Depending on the technology of the transmitting or receiving device, DTP 330 or DTP 230, the TP inputs and outputs can travel up to 330 feet (100 meters) or 230 feet (70 meters) without a loss of signal integrity. DTP CrossPoint 4K Series • Introduction...

  • Page 12: Installation

    Installation This section describes installation of the DTP CrossPoint 4K Series including connections and features. Topics that are covered include: • Rear Panel Front Panel • Rear Panel ATTENTION: Remove system power before making all connections. • Débranchez l’alimentation du système avant de faire •...
  • Page 13 12 to wire the connectors. TP connectors ATTENTION: Do not connect this port to a computer data or • telecommunications network. Ne connectez pas ces port à des données informatiques • ou à un réseau de télécommunications. DTP CrossPoint 4K Series • Installation...
  • Page 14 RJ-45 ports using TP cables. See on page 12 to wire the connector. connectors NOTE: The signal output on the nB TP output (such as 5B) is duplicated on HDMI output nA (such as 5A). DTP CrossPoint 4K Series • Installation...

  • Page 15: Audio Inputs And Outputs

    Amp output 1 (SA [stereo] model, see figure 4) — Plug passive, 4 ohm or 8 ohm speakers to this 5 mm, 4-pole captive screw connector to receive CLASS 2 WIRING the amplified audio from output 1. DTP CrossPoint 4K Series • Installation...

  • Page 16: Serial And Ir Insertion Connections

    HDBT PWR OUT = 6W HDBT 100-240V ~ -- A MAX RS-232 +48V LINK LINK MIC/LINE OVER TP RS-232 Tx Rx Tx Rx 50-60 Hz Figure 7. Serial and IR Insertion Connections, 8x4 Matrix DTP CrossPoint 4K Series • Installation...

  • Page 17: Control Connections

    IPCP Control Processor and Remote Port, 8x4 Matrix NOTE: Figure 8 and figure 9 show features for all models. Actual models can have either a LAN port (item ) or a control processor (item ), but not both. DTP CrossPoint 4K Series • Installation...

  • Page 18: Switcher Reset

    For different reset levels, press and hold the recessed button while the switcher is running or Reset while you power up the switcher. See the DTP CrossPoint 4K Series User Guide, at www.extron.com. DTP CrossPoint 4K Series • Installation...

  • Page 19: Power

    The shield it fastens to is very thin and can easily be stripped. Ne serrez pas trop la vis de montage du connecteur • HDMI. Le blindage auquel elle est attachée est très in et peut facilement être dénudé DTP CrossPoint 4K Series • Installation...
  • Page 20 LAN port to an Ethernet LAN. Crossover cable (see igure 14) — • • LAN ports — UTP or STP for direct connection between the DTP CrossPoint 4K Series and a connected computer. Crossover Cable Straight-through Cable Pins: 12345678...
  • Page 21 Use the following Extron XTP DTP 24 SF/UTP cables and connectors for the best performance: XTP DTP 24/1000 Non-Plenum 1000' (305 m) spool 22-236-03 XTP DTP 24P/1000 Plenum 1000' (305 m) spool 22-235-03 XTP DTP 24 Plug Package of 10 101-005-02 DTP CrossPoint 4K Series • Installation...
  • Page 22 Gnd (Sleeve, ) Jumper Unbalanced Mono (Mic) Input Balanced Mono (Mic) Input No Ground Here Ring Sleeves Sleeves Ring No Ground Here Unbalanced Stereo Output Balanced Stereo Output Figure 15. Audio Input and Output Connector Wiring DTP CrossPoint 4K Series • Installation...
  • Page 23 RS-232 Device Rx Tx Tx/Rx Pins Tx Rx IR Device Figure 16. RS-232 and IR Connector Wiring NOTE: The length of exposed wires is important (see the audio connectors above for more information). NOTES DTP CrossPoint 4K Series • Installation...

  • Page 24: Front Panel

    A front panel Configuration port connection and a rear panel Remote port connection can both be active at the same time. If commands are sent simultaneously to both, the command that reaches the processor first is handled first. DTP CrossPoint 4K Series • Installation...

  • Page 25: Front Panel Operations

    Audio or video can be broken away (tied by itself) by selecting only the button or only the Video Audio button. Press and release the desired input button. The button lights to indicate the selection. DTP CrossPoint 4K Series • Front Panel Operations...

  • Page 26: (And Muting Outputs)

    Press an output button. The buttons for the tied input and all tied outputs light. Press the button again to exit View mode. All inputs and View output buttons return to an unlit state. DTP CrossPoint 4K Series • Front Panel Operations...

  • Page 27: Assigning A Logo To An Output

    VOLUME to increase the program volume or mic volume. Rotate the knob counterclockwise to decrease volume. The LED ladder indicates the approximate volume; the more LEDs are lit, the higher the volume. DTP CrossPoint 4K Series • Front Panel Operations...

  • Page 28: Setting The Front Panel Locks (Executive Modes)

    • Setting audio volume • Changing Lock modes • The advanced function covered in this guide is setting audio output mutes. The switcher is shipped from the factory in Lock mode 2. DTP CrossPoint 4K Series • Front Panel Operations...

  • Page 29: Selecting Lock Mode 2 Or Toggling Between Mode 2 And Mode 0

    2 seconds. Lock mode 1 Lock mode 2 CONTROL VIDEO AUDIO VIDEO AUDIO VIDEO AUDIO ENTER PRESET VIEW VIDEO AUDIO Press and hold Press and hold for 2 seconds. for 2 seconds. DTP CrossPoint 4K Series • Front Panel Operations...

  • Page 30: Remote Control

    Remote Control This section describes using the remote control features of the DTP CrossPoint 4K Series. Topics that are covered include: • Selected SIS Commands Installing and Starting the Control Programs • Accessing the HTML Pages • Selected SIS Commands...

  • Page 31: Number Of Connections

    The tables that begin on the next page are a partial list of SIS commands. For a complete listing, see the DTP CrossPoint 4K Series User Guide at www.extron.com. Common SIS Command Symbols The following symbols are used throughout the command and response table, which starts on the next page: •...

  • Page 32: Sis Command And Response Table For Matrix Switcher Commands

    SIS Command and Response Table for Matrix Switcher Commands Command SIS Command Response Additional Description (Host to Unit) (Unit to Host) Create ties • NOTES: Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02$03*03%4*4$. • The matrix switchers support 1- and 2-digit numeric entries (1*1! or 02*02%).
  • Page 33 Command SIS Command Response Additional Description (Host to Unit) (Unit to Host) HDCP status View input HDCP status HDCP View HDCP status of all inputs IHDCP View output HDCP status HDCP View HDCP status of all outputs Includes mirrored outputs (such as 5A, 5B, 6A, 6B for 10x8) for a OHDCP total of two more s than the number of outputs (10 for 10x8).
  • Page 34 Command SIS Command Response Additional Description (Host to Unit) (Unit to Host) Input audio selection Input audio selection AFMT AfmtI Example: I1*0AFMT AfmtI01*0 Auto (0): Digital audio takes priority over analog audio. View input audio selection AFMT View input audio all selections IAFMT Each is the auto, analog, or HDMI selection of an audio...
  • Page 35 Command SIS Command Response Additional Description (Host to Unit) (Unit to Host) Recall a preset Recall a preset X1#] Recall preset . Command character is period. View video and audio mutes View output mutes Each response is the mute status of an output, starting from output 1.

  • Page 36: Installing And Starting The Control Programs

    Required for full operation of switcher DSP functions. It also provides some limited control of the switcher non-DSP functions. See the DTP CrossPoint 4K Series User Guide and the program Help ile for more information. Product Configuration Software (PCS) — Conigures the video functions of the switcher, including creating video and audio ties saving logos.
  • Page 37 Conirmation Dialog Box Click to conirm that you want to run the installation (see igure 21, Follow the on-screen instructions. The installation program creates the necessary directories and folders and installs the programs. DTP CrossPoint 4K Series • Remote Control...

  • Page 38: Starting The Product Coniguration Software

    NOTE: The factory default IP address is 192.168.254.254. The PCS opens a DTP CrossPoint window (see igure 23). Operate the program as described in the DTP CrossPoint 4K Series User Guide, at www.extron.com, and the built-in Help ile. Figure 23.

  • Page 39: Starting The Dsp Conigurator Program

    Extron recommends connection via an Ethernet LAN port for the DSP Configurator program. Start the DSP Conigurator program, as follows: Click Start > Programs > Extron Electronics > DSP . The DSP Conigurator Configurator > DSP Configurator screen opens (see igure 24).
  • Page 40 PCS. This protects the DSP settings against inadvertent changes made by the more basic PCS audio adjustment capabilities. This software lock can be overridden, but Extron STRONGLY advises against doing so. DTP CrossPoint 4K Series • Remote Control...

  • Page 41: Accessing The Html Pages

    HTML start-up page. The switcher is ready for operation via HTML remote control. If the switcher is password-protected, the switcher displays dialog box (see igure 26). Authentication Required Figure 26. Authentication Required Dialog Box DTP CrossPoint 4K Series • Remote Control...
  • Page 42 The switcher displays the HTML start-up page (see igure 27). The switcher is ready for operation via HTML remote control. Figure 27. HTML Startup Page, Shown Connected to DTP CrossPoint 108, in Google Chrome DTP CrossPoint 4K Series • Remote Control...
  • Page 43 In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.
  • Page 44 +1.919.850.1001 FAX +81.3.3511.7655 +4000.EXTRON +81.3.3511.7656 FAX +4000.398766 Inside China Only Extron Asia Extron Middle East Extron Korea +800.7339.8766 +971.4.2991800 +82.2.3444.1571 +86.21.3760.1568 Inside Asia Only +971.4.2991880 FAX +82.2.3444.1575 FAX +86.21.3760.1566 FAX +65.6383.4400 +65.6383.4664 FAX © 2016 Extron Electronics All rights reserved. www.extron.com...

Table of Contents