Table of Contents
Advertisement
Command
Commands Specific to SMX SDI/HD-SDI Boards
Output Re-clocking Per Slot
Set output reclocker per slot
Read reclocker
List DSVP (Digital Sync Validation Processing)
DSVP for VGA and RGBHV
List individual sync (DVSP)
Unit responds 0000.00, 0000.00 if no connection or an error is found.
NOTE:
List all input sync (DVSP)
DSVP (Signal Present) for Composite/S-video/DVI/DVI-Pro/HDMI Boards
List all input sync (DVSP)
List individual signal present per slot is not available on this board. Unit responds with error E14.
NOTE:
DSVP (Signal Present and Rate/Reclocker) for SDI/HD-SDI Boards
List individual sync (DVSP)/slot
Unit responds 0000 if no connection, no ties, or an error is found.
NOTE:
List all sync (DVSP)/slot
DSVP (Link Present) for Fiber Optic Boards
List all input (DVSP)
List individual signal present per slot is not available on this board. Unit responds with error E14.
NOTE:
Fiber Optic Board Status
View Fiber transceiver module
installed
X!
NOTES:
= Input number
X#
= Output Number
X*
= Fiber optic transceiver module
X1)
= Output rate
X1%
= Sync frequency
X1*
= Reclocker rates for SDI/HD-SDI board
X1(
= Signal status where
X3)
= Slot address
ASCII Command
Response
(Host to Switcher)
(Switcher to Host)
X3)
X#
X1*
*
*
=
Rte
X3)
X#
X1*]
*
=
X3)
X!
X1%
*
LS
X3)
X3)
X1(
*0LS
X3)
X3)
X1(
*0LS
X3)
X3)
X#
X1)]
*
LS
X3)
X3)
X1(
*0LS
X3)
X3)
X1(
*0LS
X3)
X3)
X*
1
0*
I
Inf
01 - <maximum number of inputs>
01 - <maximum number of outputs>
0 = no module installed
1 = multimode module
2 = singlemode module
---- = bypass mode
0000 = no connection (rate mismatch)
nnnn = actual rate
xxx.xx in Hz or kHz
00 = autodetect (default)
01 = bypass the reclocker
0 = no signal at input
1 = signal at input (H sync)
2 = signal at input (V sync)
3 = signal at input (H and V sync) or receive link presence
01 - 10
SMX System MultiMatrix Switcher • SIS Configuration and Control
X3)
X#
X1*]
*
*
X1%
]
H
V
,
X!
1
X1%
H
X1%
V
]
FRQ
,
,
n
1
X1(
2
X1(
]
...
n
X1(
X1(
X1(
]
1
2
FRQ00*
...
X1(
X1(
]
1
2
n
...
X1(
1
X1(
2
X1(
n
]
...
FRQ0*
X#
X1)]
FRQ
*
n
1
X1(
2
X1(
]
...
n
X1(
1
X1(
2
X1(
]
FRQ0*
...
n
1
X1(
2
X1(
]
...
n
X1(
1
X1(
2
X1(
]
FRQ0*
...
n
X*
X*
]
2
...
n
X3)
X*
1
X*
2
X*
]
*
...
Additional Description
Listed as Horizontal, Vertical.
Verbose mode 2 or 3
Verbose mode 2 or 3
Verbose mode 2 or 3
Verbose mode 2 or 3
Verbose mode 2 or 3
Verbose mode 2 or 3
Verbose mode 2 or 3
49
Advertisement
Table of Contents
