Table of Contents
Advertisement
f
SMX 44 FOX 4G MM — Connect fiber optic input cables from a signal source to input
ports and from output ports to a suitable display. LEDs light when signals are present.
1
2
IN
IN
OUT
OUT
FIBER OPTIC
g
SMX 88 HD-SDI — Connect SDI, HD-SDI, or dual link HD-SDI input sources to any
of the BNC input connectors. Connect suitable display devices to the BNC output
connectors.
1
2
3
4
SDI / HDSDI INPUTS
NOTE:
It is recommended to terminate unused I/Os with 75 ohm terminating
connectors.
h
SMX 88 VGA — Connect high resolution computer-video rate input sources to any of
the 15-pin HD female connectors. Connect suitable display devices to the 15-pin HD
output connectors.
COMPUTER IN
1
2
3
5
6
7
i
SMX 88 SV (DIN) and
BNC pairs or 4-pin mini DIN input connectors. Connect suitable display devices to the
BNC pairs or 4-pin mini DIN output connectors.
1
2
3
4
5
S-VIDEO IN
1
2
3
4
1
S-VIDEO IN
k
SMX 84 V — Connect composite video input signals to the BNC input connectors.
Connect display devices to the BNC output connectors.
1
2
3
4
VIDEO INPUTS
l
SMX 88 A — Connect stereo or mono audio input signals to any of the eight sets of
3.5 mm, 5-pole captive screw connectors marked Inputs. Wire the connector for the
appropriate signal type (see
INPUTS
1
2
3
4
5
L
R
L
R
L
R
L
R
L
Connect audio devices, such as an audio amplifier or powered speakers to the eight sets
of 3.5 mm, 5-pole captive screw connectors marked Outputs. The connectors output
the selected unamplified, line level audio (see
page 12 to properly wire an output connector).
By default, audio and video use different boards, so that audio breakaway is switched
separately. This is done via the front panel, Ethernet, or the RS-232 or RS-422 link,
allowing selection from any of the audio input sources. See
SIS Configuration and Control
HTML Control and Configuration
m
Plane address rotary switch — This 16 position rotary switch
defines a plane address for up to 16 I/O boards. To set an address,
insert a small screwdriver in the slot and rotate it to the desired
number (0-9, A-F). Each plane address is then identifiable during SMX
control and configuration.
4
3
5
IN
IN
IN
OUT
OUT
OUT
ADDRESS
DIGITAL VIDEO
5
6
7
8
1
1
ADDRESS
4
8
ADDRESS
j
SMX 84 YC
—
Connect S-video input sources to any of the
S-VIDEO
6
7
8
1
ADDRESS
S-VIDEO
2
3
4
1
S-VIDEO OUT
ADDRESS
VIDEO
5
6
7
8
1
ADDRESS
Wiring the Audio Connectors
6
7
8
1
R
L
R
L
R
L
R
L
R
ADDRESS
Wiring the Audio Connectors
on page 34,
SMX Control Software
on page 87 for control details.
SMX MD System MultiMatrix Switcher • Installation
7
8
6
IN
IN
OUT
OUT
OUT
FIBER OPTIC
2
2
3
4
4
5
5
6
7
3
6
7
SDI / HDSDI OUTPUTS
COMPUTER OUT
1
2
3
4
8
5
6
7
2
3
4
5
6
7
8
S-VIDEO OUT
2
3
4
2
3
4
VIDEO OUTPUTS
on page 12).
OUTPUTS
2
3
4
5
6
7
8
L
R
L
R
L
R
L
R
L
R
L
R
L
R
Operation
on page 13,
on page 59, or
IN
8
8
i
j
on
ADDRESS
9
Advertisement
Table of Contents
