Siemens SINAMICS G120 Function Manual page 238

Index
R
RDY (Ready), 188
Reference speed, 22, 128, 140, 153
Replace
Control Unit, 166
Gear unit, 166
Hardware, 166
Motor, 166
Power Module, 166
Reset
Parameter, 107
Response time, 209
Risk assessment, 17
Rolling shutter gate, 16
S
S7-300, 90
SAFE, 20, 23, 25, 57, 58, 59, 60, 61, 63, 65, 67, 68,
69, 70, 189, 194
Safe Acceleration Monitor (SAM), 22, 24
Safe Brake Ramp, 21, 22, 31, 32
Safety functions, 14
Activating the, 75
Safety integrity level, 210
Safety relay, 80, 85, 86, 87
Save parameters, 161
SBC (Safe Brake Control), 14
SBR (Safe Brake Ramp), 21, 22, 31, 32
SDI
Abort due to SS1, 63
Abort due to STO, 59
Constraint, 19
Diagnostics, 42, 44, 45, 46, 47, 59, 63, 68
Discrepancy, 202
Fault response, 201
Function test, 174
Selection when SLS is active, 67
Selection when SSM is active, 70
Switch off the motor, 44
Time response, 42
SDI (Safe Direction), 14, 42
Serial number, 167
Series commissioning, 163, 166
Service personnel, 11
Setpoint speed limit, 130, 142, 155
Shutdown speed, 24, 129, 141, 154
SIL (Safety Integrity Level), 210
SINAMICS G120
CU240E-2, 14, 75
CU240E-2 DP, 14
236
CU240E-2 DP-F, 14, 75
CU240E-2 F, 14, 75
CU240S DP-F, 14
CU240S PN-F, 14
SINAMICS G120C, 14, 75
SIZER, 230
SLS
Abort due to SS1, 61
Abort due to STO, 58
Constraint, 19
deselect, 34
Diagnostics, 30, 31, 34, 35, 38, 39, 40, 58, 61, 67
Discrepancy, 200
Fault response, 199, 203
Function test, 173
Level, 32, 36
Monitoring mode, 28
Monitoring threshold, 32, 130, 142, 155
Response, 130, 142, 155
select, 30, 34
Selection when SDI is active, 68
Selection when SSM is active, 69
Setpoint speed limit, 130, 142, 155
Switch off the motor, 38
Switching monitoring threshold, 32
Switching over monitoring, 36
Time response, 28, 30, 31, 34, 35
SLS (Safely Limited Speed), 14, 28
Speed monitoring, 190
Speed ratio, 125, 136, 149
Spindle drive, 16
SS1
Abort due to STO, 57
Braking behavior, 23, 25
Constraint, 19
Delay, 22, 32
Delay time, 24, 128, 129, 140, 141, 153, 154
Diagnostics, 23, 25, 26, 57
Discrepancy, 198
Enable, 23, 25
Fault response, 197
Function test, 172
Monitoring mode, 21
Monitoring time, 22, 128, 140, 153
Principle of operation, 21
Reference speed, 22, 128, 140, 153
Reference velocity, 128, 140, 153
select, 23, 25
Shutdown speed, 24, 129, 141, 154
Switch off the motor, 26
Time response, 21, 23, 25
Tolerance, 24
Safety Integrated Function Manual, SINAMICS G120 and G120C
Function Manual, 01/2011, FW 4.4, A5E03052391B AB