Establishing A Direct Wireless Connection To The Smart Hub; Service - Lennox iComfort S30 Installation And Setup Manual

E D W
staBlIshIng a IrECt IrElEss
IMPORTANT
If the connection between the iComfort Mobile Setup application and Smart
Hub is idle for three (3) minutes, the Smart Hub will auto-disconnect from the
mobile device. Repeat procedures to reconnect.
1. Download and install the iComfort Mobile Setup application.
NOTE: It is recommend that when using the iComfort Mobile Setup application
to commission the system, remove the HD Display from the Mag-
Mount before starting. Once commissioning is completed, reattach the
HD Display to the Mag-Mount.
2. Go to the Smart Hub and press the commissioning button located on
the side of the unit (see "Figure 2. Smart Hub Indicators and External
Components" on page 4 for location of button).
3. The commissioning status LED will start blinking green for two minutes.
During this time the Smart Hub will broadcast its Wi-Fi identifier (SSID).
4. Go to your mobile device's Wi-Fi connection tool and locate the Smart
Hub Wi-Fi broadcast identifier. A typical example of a identifier (SSID) is
DIRECT-XY12-3456.
NOTE: Refer to your mobile device's owners manual on how to use your Wi-Fi
Connection tool.
5. Connect to the Smart Hub by using the last eight digits of the Smart Hub
SSID as the password. In this example, it would be XY123456).
6. Once the mobile device is connected to the Smart Hub, the commissioning
Status LED will turn solid green.
7. Start the iComfort Mobile Setup application and make sure you are
connected to the correct Smart Hub by checking the serial number.
8. Touch the remote-in tab on the iComfort Mobile Setup application home
screen. This will take you to the commissioning screen.
9. You can use the information provided in "Commissioning (Using the HD
Display)" on page 17 to complete the commissioning process using the
iComfort Mobile Setup application.
10. If the system has not been commissioned it will go to commissioning screen
automatically. If the system has already been commissioned it will go to
dealer control center.
11. Once the commissioning is completed, exit the iComfort Mobile Setup
application.
12. Go to the mobile device's Wi-Fi tool and manually disconnect from the
Smart Hub.
C s h
onnECtIon to thE mart uB
13. Once disconnected, the Smart Hub commissioning LED will change to
solid blue.
14. Reinstall the HD Display on the Mag-Mount.
s
ErvICE
To use iComfort Mobile Setup application as a service tool, the commissioning
of the system must have already been completed.
1. Download and install the iComfort Mobile Setup application if not already
installed.
2. Go to the Smart Hub and press the commissioning button once.
3. The LED will start blinking green for two minutes. During this time the Smart
Hub will broadcast its Wi-Fi identifier (SSID).
4. If this is the first time connecting to the target Smart Hub then go to your
mobile device's Wi-Fi connection tool and locate the Smart Hub Wi-Fi
broadcast identifier. A typical example of a identifier (SSID) is DIRECT-
XY12-3456.
5. If your mobile device had already connected previously to the target Smart
Hub, then touch the applicable Smart Hub SSID on the list and skip to step
7.
NOTE: Refer to your mobile device's owners manual on how to use our Wi-Fi
Connection tool.
6. Connect to the Smart Hub by using the last eight digits of the Smart Hub
SSID as the password (XY123456) for example.
7. Once connected to the mobile device the Smart Hub commissioning LED
will turn solid green.
8. Start the iComfort Mobile Setup application and make sure you are
connected to the correct Smart Hub by checking the serial number.
9. Touch the remote-in tab on the iComfort Mobile Setup application home
screen.
10. If the system has not been commissioned it will launch the commissioning
screen. If the system has already been commissioned it will go to dealer
control center.
11. Once servicing is completed, exit the iComfort Mobile Setup application.
12. Go to the mobile device's Wi-Fi tool and manually disconnect from the
Smart Hub.
13. Once disconnected the Smart Hub LED will change to a solid blue.
16