Alternative Method; Multiple Smart Hubs; Restarting Smart Hub; Commissioning (Using The Hd Display) - Lennox iComfort S30 Installation And Setup Manual

a m
ltErnatIvE EthoD
From the home screen, go to menu > settings > advanced settings > pair
Smart Hub to iComfort dealer mobile application selection. It will auto connect
to dealer application and start you at the dealer control center screen. The
following screen will appear and show the status of the connection. Once
connected the screen will automatically disappear.
settings settings
wi- wi- local local
smart away smart a aw w ay y on
Feels L Feels Like Like e o
fan fan auto
heat & heat & cool co o o o l
humidity humid ity y
iHarmony zoning iHarmo ony y zo o n
noti ca noti cations ati i ons
genera general al
display display y
Figure 15. Pairing
home info home info
account account
m s h
ultIplE mart uBs
Multiple Smart Hubs in a home can be assigned to a group (up to nine groups
with up to eight (8) Smart Hubs in each group). All Smart Hubs in a group can
communicate with other Smart Hubs in the same group over the home Wi-Fi
network.
Default Group ID is 1. Range is 0 to 9.
For example, seven Smart Hubs in a home can be divided up for example as 1
in Group 1 and six in Group 2 or 4 in Group 1 and 3 in Group 2. Smart Hubs in
Group 1 will not be able to see or interact with the Smart Hubs in Group 2. This
allows the intentional isolation of the Smart Hub for the master bedroom from
the Smart Hub for the children's area, for example.
NOTE: If a Smart Hub is set to Group 0, it will not communicate with other
Smart Hubs.
r s h
EstartIng mart uB
Pressing the Smart Hub button for more than five seconds will reboot the Smart
Hub.
advanced settings advanced settings
view dealer dashboard view i d d eal l er d d a h shb b oard d
now broadcasting...
restart
Connect to the Smart Hub from
the dealer iComfort mobile app
pair Smart Hub to icomfort dealer mobile app
stop

Commissioning (Using the HD Display)

The following procedures are written for commissioning the system using the
HD display interface.
When power is first applied to the system all iComfort devices attached to the
system (air handler or furnace, outdoor unit or zoning control) will automatically
be configured using optimal factory default settings based on system type,
capacity and other configuration considerations.
NOTE: If there is an PureAir S air purification system installed, during
commissioning the blower will turn on and run at three different CFM
settings for the PCO filter calibration to take place. This may be well in
advanced before the display is fully up and running. This is a normal
process. The blower may run as long as 90 seconds at each CFM
setting to complete the filter calibration .
B - s
oot up CrEEn
When power is applied to the system, the HD Display will display a welcome
screen.
If there is an issue with communication between any components attached to
the thermostat, a critical alert message will appear on the screen. The alert
message will provide detail information concerning the possible cause. Once
the issue is corrected and power is restored to the system the first screen in the
initial commissioning sequence will appear.
Below is an example of a communication error message.
IComfort cannot communicate with the equipment
IComfort is unable to connect to the Smart Hub device
If problem persists, please contact your iComfort dealer at
Figure 16. Communication Error Message Example
l B s
oW attEry tatus
If a critical low battery screen is displayed, the system will automatically start
charging the HD Display internal battery. On the screen the word "charging" will
appear. Once "charging" disappears (typically 3 to 10 minutes) then the display
will automatically start-up.
17
alert
1-800-555-8888
For additional support, contact Lennox at
1-800-9-LENNOX or visit www.lennox.com/support