Kyocera TASKalfa 3510i Service Manual page 520

No. Content
F21X
An error is detected at the
F22X Image processing section
F23X
An error is detected at the
F24X
System management section
An error is detected at the
F25X
Network management section
F26X
F27X
An error is detected at the
F28X
System management section
F29X
F2AX
An error is detected at the
F33X
Scan management section
An error is detected at the
F34X
Panel management section
An error is detected at the
F35X
Print control section
An error is detected at the
F36X
Print management section
An error is detected at the
F37X
FAX management section
An error is detected at the
F38X Authentication/permit
management section
F39X KMAS管理部での異常検知
F3AX
F3BX
F3CX
F3DX
F3EX
F3FX An error is detected at the
F40X Entity management section
F41X
F42X
F43X
F44X
F45X
Check procedure & check point
1) Check contact of the DDR memory and check function.
2) Format the HDD and check function. (U024 FULL formatting)
3) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
4) Replace the main board and check function.
5) Replace the HDD and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
1) Check contact of the DDR memory and check function.
2) Format the HDD and check function. (U024 FULL formatting)
3) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
4) Replace the main board and check function.
5) Replace the HDD and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
3) Replace the main board and check function.
4) Retrieve the USBLOG and contact the Service Administratuve Division.
(or retrieve the packet capture data depending on the reult of analysis)
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Check connection of the harness (Scan/DP board - main board) and connectors
and check function.
2) Format the HDD and check function. (U024 FULL formatting)
3) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
4) Replace the Scan/DP board and check function.
5) Replace the main board and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
3) Replace the main board and check function.
4) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
3) Execute the U671 Clear FAX back up data (FAX DIMM clear) and check function.
(Take cae of the received data since it is cleared)
4) Replace the FAX_DIMM and check function.
5) Replace the main board and check function.
6) Replace the HDD and check function.
7) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Check connection of the harness (Authentication device - Main board) and
connectors and check function.
2) Format the HDD and check function. (U024 FULL formatting)
3) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
4) Replace the main board and check function.
5) Replace the HDD and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
Team
PrintSys/
GICL
SSM/PRC
M/RPG/D
CM/ESM/
Entity
Network
SSM/PRC
M/RPG/D
CM/ESM/
Entity/KS
F
Scanner/I
nputRIP
PSO/GUI
PrintSys/
GICL
OS/BMC
Job/Fax/S
ervice
SSM/PRC
M/RPG/D
CM/ESM/
Entity
SSM/PRC
M/RPG/D
CM/ESM/
Entity
SSM/PRC
M/RPG/D
CM/ESM/
Entity
2-4-15
Remark 1
[DDR2 memory contact
check]
Main board:YS1 or YS3
A certain part of the memory
be faulty. The frequency of
faiure occurrence is
dependent on the frequency
of access to the faulty bit.
The ASIC may be faulty if
the memory is not sensitive.
[DDR2 memory contact check]
Main board:YS1 or YS3
*The F248 eror is printer
A certain part of the memory be
process error. if it repeats
faulty. The frequency of failure
with a certain print data,
occurrence is dependent on the
retrieve the capture data and
frequency of access to the
USBLOG.
faulty bit. The ASIC may be
faulty if the memory is not
*This may be owing to the
-
users network environment.
-
[Main-Scan Interface]
Main board: YC11,YC25
ISC board: YC3,YC4
[Main-Panel Interface]
Main board:YC6,YC12
Panel board:YC10,YC17
-
-
[The contact check of FAX
DIMM]
Main board:YS5
-
[Main⇔KMAS Interface]
Main board:YC7
KMAS board:CN1 or CN2
-
Remark 2