Siemens Simatic ET 200S Operating Instructions Manual page 8

Table of contents
4.9 Installing the shield contact ...................................................................................................... 4-19
4.10 Applying slot number labels and color identification labels...................................................... 4-21
5 Wiring and assembly .............................................................................................................................. 5-1
5.1 General rules and regulations for operating the ET 200S ......................................................... 5-1
5.2 Operating the ET 200S on a grounded incoming supply ........................................................... 5-3
5.3 Electrical configuration of the ET 200S...................................................................................... 5-6
5.4 Wiring the ET 200S .................................................................................................................... 5-7
5.4.1 Wiring rules for the ET 200S ...................................................................................................... 5-7
5.4.2 Wiring a terminal module with screw-type terminals.................................................................. 5-8
5.4.3 Wiring a terminal module with spring terminals ......................................................................... 5-8
5.4.4 Wiring terminal modules with Fast Connect............................................................................... 5-9
5.4.5 Wiring terminal modules........................................................................................................... 5-12
5.4.6 Wiring an interface module with PROFIBUS DP interface (electrically) .................................. 5-15
5.4.7 Wiring an interface module with PROFIBUS DP interface (optically) ...................................... 5-16
5.4.8 Wiring an interface module with PROFINET IO interface (electrically) ................................... 5-20
5.5 Plugging and removing electronic modules and COMPACT modules .................................... 5-22
5.5.1 Plug and label electronic or COMPACT modules .................................................................... 5-22
5.5.2 Removing and inserting modules during operation ................................................................. 5-27
6 Commissioning ....................................................................................................................................... 6-1
6.1 Safety tests prior to commissioning ........................................................................................... 6-1
6.2 Commissioning on PROFIBUS DP ............................................................................................ 6-1
6.2.1 Configuring ET 200S on PROFIBUS DP ................................................................................... 6-1
6.2.1.1 Basic principles of configuration for the ET 200S on PROFIBUS DP ....................................... 6-1
6.2.1.2 Grouping modules for the configuration..................................................................................... 6-3
6.2.1.3 Grouping digital input modules .................................................................................................. 6-5
6.2.1.4 Grouping digital output modules ................................................................................................ 6-6
6.2.1.5 Grouping motor starters ............................................................................................................. 6-7
6.2.1.6 Example of a Configuration........................................................................................................ 6-7
6.2.2 Commissioning and startup of ET 200S on PROFIBUS DP...................................................... 6-9
6.2.2.1 Setting the PROFIBUS Address ................................................................................................ 6-9
6.2.2.2 Commissioning ET 200S on PROFIBUS DP ........................................................................... 6-10
6.2.2.3 Startup of the ET 200S on PROFIBUS DP .............................................................................. 6-12
6.3 Commissioning on PROFINET IO ........................................................................................... 6-13
6.3.1 Configuring the ET 200S on the PROFINET IO....................................................................... 6-13
6.3.2 Assigning device names to the I/O device ............................................................................... 6-14
6.3.3 Grouping modules for the configuration................................................................................... 6-16
6.3.4 Commissioning and startup of ET 200S on PROFINET IO ..................................................... 6-18
7 Functions ................................................................................................................................................ 7-1
7.1 Direct data exchange on PROFIBUS DP................................................................................... 7-1
7.2 Cycle synchronization on the PROFIBUS DP............................................................................ 7-3
7.2.1 Basics......................................................................................................................................... 7-3
7.2.2 Assigning the parameters for cycle Synchronization on the PROFIBUS DP ............................ 7-4
7.2.3 Fault correction during isochronous operation on PROFIBUS DP ............................................ 7-7
viii
Operating Instructions, 12/2005, A5E00515771-03
ET 200S