Page 195
Your Address: Name: Siemens AG Company: A&D AS SM ID Position: Postfach 1963 Street: D-92209 Amberg Postal code / Place: Telefax: +49(9621)80-3103 Email: mailto:doku@ad.siemens.de Phone: Fax: Your Feedback as regards the S7 Distributed Safety Dear SIMATIC user, Our goal is to provide you information with a high degree of quality and usability, and to continuously improve the SIMATIC documentation for you.
Page 196
Please specify the documents, for which you want to answer the questions below: Manual S7 Distributed Safety, Manual ET 200eco, Distributed I/O Configuring and Programming Fail-Safe I/O Module Manual S7-300, Fail-Safe System Description Signal Modules Safety Engineering in SIMATIC S7 Getting Started S7 Distributed Safety Manual ET 200S, Distributed I/O System...
Page 197
______________ Introduction ET 200S Distributed I/O F Technology Product Information for the Distributed I/O System ET 200S, Fail-Safe Systems Digital Electronics Module Manual ______________ 1 F-RO DC24V/5A AC24..230V/5A ET 200S Distributed I/O F Technology Product Information for the Distributed I/O System ET 200S, Fail-Safe Systems Manual Product information 07/2006...
Page 198
Trademarks All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Table of contents Introduction............................. 1-1 Digital Electronics Module 1 F-RO DC24V/5A AC24..230V/5A............... 2-1 Properties of the EM 1 F-RO DC24V/5A AC24..230V/5A ............2-1 Address assignment in the F-CPU..................... 2-2 Terminal Assignment for EM 1F-RO DC24V/5A AC24..230V/5A..........2-3 Wiring of the EM 1 F-RO DC24V/5A AC24..230V/5A..............2-6 Diagnosis of the EM 1 F-RO DC24V/5A AC24..230V/5A............
Page 200
Table of contents Product Information for the Distributed I/O System ET 200S, Fail-Safe Systems Manual Product information, 07/2006, A5E00825271-01...
Introduction Scope ET 200S, Fail-Safe Modules This product information supplements the manual A5E00103686-04, Version 07/2005 and describes the new digital electronics module 1 F-RO DC24V/5A AC24..230V/5A. Cross references in this product information In order to simplify matters, all cross references to sections of the above-referenced manual are specified without giving the full name of the manual (e.g.
Page 202
Introduction Product Information for the Distributed I/O System ET 200S, Fail-Safe Systems Manual Product information, 07/2006, A5E00825271-01...
Digital Electronics Module 1 F-RO DC24V/ 5A AC24..230V/5A Properties of the EM 1 F-RO DC24V/5A AC24..230V/5A Order number 6ES7 138-4FR00-0AA0 Properties The digital electronics module 1 F-RO DC24V/5A AC24..230V/5A has the following properties: • 1 relay-output (2 make contact elements) •...
Digital Electronics Module 1 F-RO DC24V/5A AC24..230V/5A 2.2 Address assignment in the F-CPU Address assignment in the F-CPU Address Assignment The EM 1 F-RO DC24V/5A AC24..230V/5A is assigned to the following address areas in the F-CPU: • For S7 Distributed Safety: in the area of the process image •...
Digital Electronics Module 1 F-RO DC24V/5A AC24..230V/5A 2.3 Terminal Assignment for EM 1F-RO DC24V/5A AC24..230V/5A Terminal Assignment for EM 1F-RO DC24V/5A AC24..230V/5A Front View Figure 2-1 Front view EM 1 F-RO DC24V/5A AC24..230V/5A Warning The status display of the output may not be analyzed for activities dealing with safety. Product Information for the Distributed I/O System ET 200S, Fail-Safe Systems Manual Product information, 07/2006, A5E00825271-01...
Page 206
Digital Electronics Module 1 F-RO DC24V/5A AC24..230V/5A 2.3 Terminal Assignment for EM 1F-RO DC24V/5A AC24..230V/5A Terminal assignment The figure below depicts the terminal assignment of the EM 1 F-RO DC24V/5A AC24..230V/5A for the applicable terminal modules TM-E30S44-01, TM-E30C44-01, TM- E30S46-A1, and TM-E30C46-A1. Figure 2-2 Terminal assignment TM-E...44-01/TM-E...46-A1 for EM 1 F-RO DC24V/5A AC24..230V/5A...
Page 207
Digital Electronics Module 1 F-RO DC24V/5A AC24..230V/5A 2.3 Terminal Assignment for EM 1F-RO DC24V/5A AC24..230V/5A Table 2-3 Terminal assignment of TM-P30S44-A0 and TM-P30C44-A0 Terminal Designation IN P Terminal for control voltage DC 24V IN M Terminal for control voltage ground AUX 1 at TM-E...46-A1: AUX 1 bus implemented.
Digital Electronics Module 1 F-RO DC24V/5A AC24..230V/5A 2.4 Wiring of the EM 1 F-RO DC24V/5A AC24..230V/5A Wiring of the EM 1 F-RO DC24V/5A AC24..230V/5A Block diagram Figure 2-3 Block diagram of the EM 1 F-RO DC24V/5A AC24..230V/5A Product Information for the Distributed I/O System ET 200S, Fail-Safe Systems Manual Product information, 07/2006, A5E00825271-01...
Page 209
Digital Electronics Module 1 F-RO DC24V/5A AC24..230V/5A 2.4 Wiring of the EM 1 F-RO DC24V/5A AC24..230V/5A Wiring diagram Figure 2-4 Wiring diagram of the EM 1 F-RO DC24V/5A AC24..230V/5A Warning * Please use an external fuse for the load current circuit with the following properties to protect the relay contacts from overload and short circuiting: Fusible cutout, 6 A of the operating class gL/gG DC 24V-supply terminal...
Page 210
Digital Electronics Module 1 F-RO DC24V/5A AC24..230V/5A 2.4 Wiring of the EM 1 F-RO DC24V/5A AC24..230V/5A Load voltage and load connection The relay output connections are potential-free contacting elements. This means that the supply voltage must be provided externally. Connect the load supply (supply 1) and the load (load 1) in series on the connections OUT 1 (terminals 9;13)/(terminals10;14).
Digital Electronics Module 1 F-RO DC24V/5A AC24..230V/5A 2.5 Diagnosis of the EM 1 F-RO DC24V/5A AC24..230V/5A Diagnosis of the EM 1 F-RO DC24V/5A AC24..230V/5A Output status display The output status display on the F-RO-module has the following behavior: • Relay not activated: LED does not light up •...
Page 212
Digital Electronics Module 1 F-RO DC24V/5A AC24..230V/5A 2.6 Technical Data of the EM 1 F-RO DC24V/5A AC24..230V/5A Technical Specifications Voltages, Currents, Potentials Control voltage DC 20.4 to 28.8 V (supply through F-DO fail-safe output) Total current over both channels Horizontal installation •...
Page 213
Digital Electronics Module 1 F-RO DC24V/5A AC24..230V/5A 2.6 Technical Data of the EM 1 F-RO DC24V/5A AC24..230V/5A Technical Specifications Current consumption From backplane bus • max. 10 mA From control voltage (IN P, IN M) • max. 100 mA Power dissipation of the module avg.
Digital Electronics Module 1 F-RO DC24V/5A AC24..230V/5A 2.7 Response Times of EM 1 F-RO DC24V/5A AC24..230V/5A Switching capacity and service life of the contacts The following table indicates the switching capacity and service life of the contacts. Service life can be increased beyond the value indicated in the following table by using an external protective element.
Page 215
Index Accessories Order numbers Order numbers, 1-1 of accessories, 1-1 Address Assignment Output F-modules in F-CPU, 2-2 Status display, 2-9 User data in F-CPU, 2-2 Safety parameters EM 1 F-RO DC24V/5A AC24..230V/5A EM 1 F-RO DC24V/5A AC24..230V/5A, 2-9 Order number, 2-1 Status display Safety parameters, 2-9 Output, 2-9...