Agilent Technologies 1260 Infinity II Bio Flexible Pump Manuals

Manuals and User Guides for Agilent Technologies 1260 Infinity II Bio Flexible Pump. We have 1 Agilent Technologies 1260 Infinity II Bio Flexible Pump manual available for free PDF download: User Manual

Agilent Technologies 1260 Infinity II Bio Flexible Pump User Manual

Agilent Technologies 1260 Infinity II Bio Flexible Pump User Manual (310 pages)

Brand: Agilent Technologies | Category: Laboratory Equipment | Size: 34.34 MB

Table of Contents

Table of Contents
5
1 Introduction

9
- Agilent 1260 Infinity II Flexible Pump
  
  10
  - Product Description
    10
  - Features
    11
- Agilent 1260 Infinity II Bio Flexible Pump
  
  12
  - Product Description
    12
  - Features
    13
- Operating Principle
  
  14
- Positions of the Multi Purpose Valve
  
  16
- Leak and Waste Handling
  
  20
  - Leak Sensor
    23
  - Waste Concept
    24
2 Site Requirements and Specifications

25
3 Using the Module

37
4 Preparing the Pump

84
- Capillary Coding Guide
  85
- Installing Capillaries
  88
5 How to Optimize the Performance of Your Module

92
6 Troubleshooting and Diagnostics

105
- User Interfaces
  106
- Agilent Lab Advisor Software
  107
- Pump Leak Rate Test
  108
- Troubleshooting the Pump Leak Rate Test
  111
- System Pressure Test
  113
- Pump Self Test
  115
7 Error Information

119
- What Are Error Messages
  121
- General Error Messages
  122
- Timeout
  122
- Shutdown
  123
- Remote Timeout
  124
- Lost CAN Partner
  124
- Leak Sensor Short
  125
- Leak Sensor Open
  126
- Compensation Sensor Open
  126
- Compensation Sensor Short
  127
- Fan Failed
  128
- Leak
  129
- Pump Error Messages
  130
- Pressure of Quaternary Pump above Upper Limit
  130
- Pressure below Lower Limit
  131
- Target Pressure Not Reached for Quaternary Pump Degasser
  131
- Solvent Counter Exceeded Limit
  132
- Waste Counter Limit Exceeded
  132
- Flow Rate Limit Exceeded
  133
- Quaternary Pump Shutdown During Analysis
  133
- Reading the Pump Encoder Tag Failed
  134
- Writing the Pump Encoder Tag Failed
  134
- Pump Drive Blocked or Encoder Failed
  135
- Drive Current too Low
  135
- Drive Current too High
  136
- Drive Timeout
  136
- Overcurrent of Pump Drive
  137
- Deliver Underrun
  137
- Defect Connection between Main Board and Pump Drive Encoder
  138
- Pump Drive Encoder Defect
  138
- Multipurpose Valve Failed
  138
- Reading of Multipurpose Valve Tag Failed
  139
- Pump Drive Encoder Rollover
  139
- Drive Position Limit
  139
- Insufficient Power of Drive Encoder LED
  140
- Drive Encoder Error
  140
- Writing the Multipurpose Valve Tag Failed
  140
- Unknown Multipurpose Valve Type
  141
- Pump Drive Encoder Error
  141
- Pump Drive Error
  141
- Maximum Stroke Is too Short
  142
- Pump Drive Stop Not Found
  142
- Timeout: Wait for Composition
  143
- Timeout: Wait for Run Volume
  143
- Timeout: Wait for Volume
  144
- Timeout: Wait for Flow
  144
- Timeout: Wait for Pressure
  145
- Drive Encoder Failed
  145
- Drive Phases Differ too Much in Electric Resistance
  146
- Degasser's Pressure Limit Violation
  146
- Seal Wash Pump was Missing When Tried to Turn on
  147
- Valve Hardware Overcurrent (MCGV)
  147
- Invalid Degasser Pressure Signal
  148
8 Maintenance

149
- Introduction to Maintenance
  151
- Warnings and Cautions
  153
- Overview of Maintenance
  154
- Cleaning the Module
  155
- Install Fittings and Capillaries
  156
- Remove and Install Doors
  157
- Replace the Pressure Sensor
  159
- Replace the Inlet Weaver
  161
- Replace the Inlet Valve (G7104C)
  163
- Replace the Inlet Valve (G7131C)
  164
- Remove the Jet Weaver
  165
- Install the Jet Weaver
  167
- Replace the Seal Wash Pump Cartridge
  169
- Replace the Multi-Channel Gradient Valve (MCGV)
  170
- Replace the Four-Channel Gradient Valve (4CGV)
  172
- Release a Stuck Inlet Valve
  174
- Remove the Pump Head Assembly (G7104C)
  176
- Remove the Pump Head Assembly (G7131C)
  178
- Pump Head Maintenance (Tool Free)
  181
- Disassemble Pump Heads (G7104C)
  182
- Disassemble Pump Heads (G7131C)
  186
- Replace the Heat Exchanger (G7104C)
  190
- Replace the Heat Exchanger (G7131C)
  192
- Assemble Pump Heads (G7104C)
  194
- Assemble Pump Heads (G7131C)
  200
- Install the Pump Head Assembly (G7104C)
  206
- Install the Pump Head Assembly (G7131C)
  208
- Replace the Outlet Valve (G7104C)
  210
- Replace the Outlet Valve (G7131C)
  213
- Replace the Multipurpose Valve
  215
- Replace Parts of the Multipurpose Valve (G7104C)
  217
- Replace Parts of the Multipurpose Valve (G7131C)
  218
- Replace the High Pressure Outlet Filter or Filter Frit
  219
- Install the Inline Filter
  221
- Remove the Inline Filter
  223
- Replace Parts of the Inline Filter
  224
- Replace the Seal Wash Sensor
  226
- Replace the Module Firmware
  228
- Prepare the Pump Module for Transport
  229
9 Parts and Materials for Maintenance

231
- Overview of Main Assemblies (G7104C)
  232
- Overview of Main Assemblies (G7131C)
  234
- Flow Connections (G7104C)
  236
- Flow Connections (G7131C)
  238
- Pump Heads (G7104C)
  240
- Pump Head Assembly Parts
  241
- Primary Pump Head Parts
  242
- Secondary Pump Head Parts
  243
- Pump Heads (G7131C)
  244
- Pump Head Assembly Parts
  244
- Primary Pump Head Parts
  245
- Secondary Pump Head Parts
  246
- Multipurpose Valve (G7104C)
  247
- Multipurpose Valve (G7131C)
  248
- Cover Parts
  249
- Accessory Kit (G7104C)
  250
- Accessory Kit (G7131C)
  251
- Tool Kit
  252
10 Identifying Cables

253
- Cable Overview
  254
- Analog Cables
  256
- Remote Cables
  258
- CAN/LAN Cables
  262
- Agilent Module to PC
  263
- USB Cables
  264
11 Hardware Information

265
- Firmware Description
  266
- Electrical Connections
  269
- Serial Number Information
  270
- Rear View of the Module
  270
- Interfaces
  271
- Overview Interfaces
  273
- USB (Universal Serial Bus)
  275
- Setting the 8-Bit Configuration Switch
  276
- Special Settings
  278
- Early Maintenance Feedback
  279
- Instrument Layout
  280
12 LAN Configuration What You Have to Do First

282
- TCP/IP Parameter Configuration
  283
- Configuration Switch
  284
- Initialization Mode Selection
  285
- Dynamic Host Configuration Protocol (DHCP)
  287
- General Information (DHCP)
  287
- Setup (DHCP)
  288
- Link Configuration Selection
  290
- Manual Configuration
  291
- With Telnet
  292
- PC and User Interface Software Setup
  296
- PC Setup for Local Configuration
  296
- User Interface Software Setup
  297
13 Appendix

298
- General Safety Information
  299
- Safety Standards
  299
- General
  299
- Before Applying Power
  300
- Ground the Instrument
  300
- Do Not Operate in an Explosive Atmosphere
  301
- Do Not Remove the Instrument Cover
  301
- Do Not Modify the Instrument
  301
- In Case of Damage
  301
- Solvents
  302
- Safety Symbols
  303
- Waste Electrical and Electronic Equipment Directive
  305
- Radio Interference
  306
- Sound Emission
  307
- Agilent Technologies on Internet
  308

Advertisement

Advertisement

Related Products

Agilent Technologies Categories

Measuring Instruments Laboratory Equipment Test Equipment Water Pump

Power Supply

More Agilent Technologies Manuals