Husqvarna TC 250 2010 Workshop Manual page 398

Cylinder head
Screw TFEI M6x1-L30
Screw TFEI M6x1-L35
Screw TFEI M5-L30
Screw TFEI M5-L25
Screw TTEI M5x0.8 L.8
Special flanged screw L.23.4
Special flanged screw L.31.3
Water temperature sensor M10x1.25
Hole plug (water sensor) M10x1.25
Head stud bolt
Head stud bolt
Drive and transmission
Flanged nut M16
Timing system
Cheese-headed Phillips screw M4-
L10
Screw TEF M6-L8-D14
Screw TEF M6-L20
Special M6x1 screw
Crankcase
Screw TSEI M5-L12
Screw TEF M5x0.8-CH8-L8
Screw TSEI M6-L10
Selector spring pin M8x1.25
Screw TSEI M6-L14
Screw TEF M6x1-L55
Screw TEF M6x1-L60
Screw TEF M6x1-L70
Screw TEF M6x1-L90
Screw TEF M6x1-L20
Screw TEF M6x1-L50
Screw TEF M6-L22
Screw TEF M5-L16
Screw TCEI M5 L35
Screw TCEI M5 L40
Lubrication
1 Nm = 0.73756 ft/lb
TIGHTENING TORQUE FIGURES
TIGHTENING TORQUE FIGURES (+/- 5%) ENGINE (8000 A7028)
Cap
Cap
Cap
Cap
Blow-by labyrinth plate (+LOCTITE 243)
Head cover and fuel
Head cover
Drive gear
Flanged shaft
Chain tensioner closure
Chain tensioner
Slider (use LOCTITE 243)
Crankshaft bearing plate
(+LOCTITE 270 or LOCTITE 272)
For oil seal retaining plate
Desmo bearing plate
(use LOCTITE 270 - or LOCTITE 243)
Use LOCTITE 270 - or LOCTITE 272
Starter plate
(use LOCTITE 270 - or LOCTITE 272)
Crankcase joining
Crankcase joining
Crankcase joining
Crankcase joining
R.H. cover
R.H. cover and clutch cover
Clutch cover
Oil filter cover
Ignition cover
Ignition cover
X.2
10 Nm 1.02 Kgm
10 Nm 1.02 Kgm
5.5 Nm 0.56 Kgm
5.5 Nm 0.56 Kgm
6 Nm 0.6 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
5 Nm 0.5 Kgm
8 Nm 0.8 Kgm
40 Nm 4.1 Kgm
40 Nm 4.1 Kgm
100 Nm 10.2 Kgm
3 Nm 0.3 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
6 Nm 0.6 Kgm
6 Nm 0.6 Kgm
8 Nm 0.8 Kgm
25 Nm 2.55 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
6 Nm 0.6 Kgm
6 Nm 0.6 Kgm
6 Nm 0.6 Kgm
Part. N. 8000 H1489 (10-2009)