Cp01 Setup - Visonic PowerMaster-10 G2 Quick User Manual

5. PROGRAMMING

5.15.5 CP01 Setup

13:OPERATION MOD
Enter the "04:CP01 SETUP" menu to configure CP01 settings.
Option
01:DISARM OPTION
03:END EXIT MODE
05:CONFIRM ALARM
07:RPRT CNF ALRM
08:ENTRY DELAY 1
09:ENTRY DELAY 2
10:ABORT TIME
11:CANCEL ALARM
12:CNCEL ANOUNCE
1
Applies only when the keyfob is defined as "skip exit delay" (for further details, see the keyfob's User's Guide)
66
⋅ ⋅ ⋅
CP01 SETUP
Configuration Instructions
Certain regulations require that when the system is armed in AWAY mode, it may not be
disarmed from the outside of the house (such as by keyfobs) before entering the protected
premises and activating an "Entry Delay" zone. To answer this requirement, the
PowerMaster provides you with the following configurable options to disarm the system:
A: At "any time" (default), the system can be disarmed at all times from all devices.
B: During entry delay, the system can be disarmed only using keyfob or prox operated
devices ("on entry wrless").
C: During entry delay by code, the system can be disarmed only using PowerMaster panel
keypad ("entry + away kp.").
D: During entry delay, the system can be disarmed using keyfobs or by code using the
PowerMaster panel keypad ("on entry all.").
Define how the exit delay is terminated or restarted according to the following options:
restart+arm home (default) – During exit delay if the door was not opened, the alarm
system will be armed HOME instead of armed AWAY.
restart>reentry - Exit delay restarts when the door is reopened during exit delay. The
restart occurs once only. Restarting the exit delay is helpful if the user re-enters
immediately after going out to retrieve an item that was left behind.
door/fob/timer - When the door is closed, by pressing the AUX button on the keyfob
when the exit delay has expired, whichever first.
fob/timer - By pressing the AUX button on the keyfob
whichever first.
If two successive alarm events occur within a specific time window, the system can be
configured to report the second alarm event as a "confirmed alarm" (see section 5.6.4
option 61). You can activate this feature and set the respective time window.
Options: disable (default in USA); in 30/45/60(default)/90 minutes
Define whether the system will report a confirmed alarm.
report disable (default) - The system will not report a confirmed alarm.
report enable - The system will report a confirmed alarm.
Two different entry delays allow the user to enter the protected site (while the system is in
the armed state) via 2 specific doors and routes without causing an alarm.
Following entry, the user must disarm the control panel before the entry delay expires.
Slow-rate warning beeps start sounding once the door is opened, until the last 10 seconds
of the delay, during which the beeping rate increases. Locations No. 1 (entry delay 1) and 2
(entry delay 2) allow you to program the length of these delays.
Options: 30 (default)/45/60 seconds; 3/4 minutes
The PowerMaster can be configured to provide a delay before reporting an alarm to the
monitoring station (not applicable to alarms from FIRE, 24H SILENT, EMERGENCY, GAS
FLOOD and TEMPERATURE zones). During this delay period, the external siren will not
sound and the alarm is not reported. If the user disarms the system within the delay time,
the alarm is aborted.
Options: in 15 (default)/30/45 seconds
Define the "cancel alarm" period that starts upon reporting an alarm to the Monitoring
Station. If the user disarms the system within that time period, a "cancel alarm" message is
sent to the Monitoring Station.
/1
Options: in 5 (default)
Here you determine whether a special beep will sound when an alarm cancel event is sent to
the central station.
5/60 minutes; in 4 hours
D-304762 PowerMaster-10/30 G2 Installer's Guide
1
, or when the exit delay has expired,
1
, or