Canon iR2030 Series Service Manual page 269

#SSSW
No. Initial setting
SW34 10000000
SW35 - SW50
#MENU
No. Initial setting
01: - 04:
05: 0
06: 0
07: 10
08: 0
09: 0
10: 1
11: - 20:
#NUMERIC Param.
No. Initial setting
001:
002: 10 (10%)
003: 15 (15lines)
004: 12 (12times)
005: 4 (4sec)
006: 4 (4sec)
007: - 009:
010: 5500 (55sec)
011: 3500 (35sec)
012:
013: 1300 (13sec)
014:
015: 120 (1200ms)
016: 4 (4sec)
017: 100 (1000ms)
018: 0 (0ms)
019: 200 (2000ms)
020: 100 (1000ms)
021: 0 (0ms)
022: 200 (2000ms)
023: 4
024: 20 (-20dBm)
025: 60 (60sec)
026:
027: 0
028: - 054:
055: 60 (min)
056: 101
Function
waste toner full display setting
not used
Range of Function
setting
not used
ON/OFF NL equalizer setting
0: DIAL line monitor setting
1: SERVICEMAN [1]
2: SERVICEMAN [2]
3: OFF
0-15 transmission level setting
0: 3429 V.34 baud rate
1: 3200
2: 3000
3: 2800
4: 2743
5: 2400
0: 33.6kbs V.34 transmission speed
1: 31.2kbs
2: 28.8kbs
3: 26.4kbs
4: 24.0kbs
5: 21.6kbs
6: 19.2kbs
7: 16.8kbs
8: 14.4kbs
9: 12.0kbs
10: 9.6kbs
11: 7.2kbs
12: 4.8kbs
13: 2.4kbs
0: 50Hz pseudo CI signal frequency setting
1: 25Hz
2: 17Hz
not used
Range of setting Function
not used
(1 - 99) RTN signal transmission condition (1) setting
(2 - 9) RTN signal transmission condition (2) setting
(1 - 99) RTN signal transmission condition (3) setting
(1 - 60) NCC pause time (pre-ID code) setting
(1 - 60) NCC pause time (post-ID code) setting
not used
(0 - 9999) line connection identification time length
(0 - 9999) T.30 T1 timer (for reception)
not used
(500 - 3000) T30 EOL timer
not used
(0 - 999) hooking detection time setting
(0 - 9) fax/tel switch-over function: between line acquisition and pseudo RBTtransmission
(0 - 999) pseudo RBT signal pattern: ON time setting
(0 - 999) pseudo RBT signal pattern: OFF time (short) setting
(0 - 999) pseudo RBT signal pattern: OFF time (long) setting
(0 - 999) pseudo CI signal pattern: ON time setting
(0 - 999) pseudo CI signal pattern: OFF time (short) setting
(0 - 999) pseudo CI signal pattern: OFF time (long) setting
(0 - 7) fax/tel switch-over pseudo RBT transmission level
(0 - 20) fax/tel switch-over pseudo RBT transmission level
(0 - 999) pseudo RBT signal pattern: OFF time (long) setting
not used
(0 - 20) V21 low-speed flag preamble detection time length
not used
(0 - 480) acquisition period of enviormental log data
(0 - 999) count type select 1
Chapter 15
15-3