Teknor Industrial Computers VIPer807 Technical Reference Manual page 97

TABLE 10-4: Power Management Setup
Option Fail-safe Defaults
Power Management Mode Disabled
DOZE Mode Time Out Disabled
SLEEP Mode Time Out Disabled
SUSPEND Time Out Disabled
Video access as an activity Disabled
Pri. ISA Master as an activity Disabled
HDD Standby Time Out Disabled
LCD Standby Time Out Disabled
Resume with Modem Ring Disabled
Suspend Warning Beeps Disabled
* By default, the Power Management Mode option is set to Disabled, and all the other options read Disabled, hiding their actual default settings.
Only when the Power Management Mode option is set to Enabled, can you see the default values shown here with an asterisk (*).
TABLE 10-5: Peripheral Setup
Option Fail-safe Defaults
OnBoard IDE* Enabled
IDE LBA Mode Disabled
IDE Block Mode Disabled
IDE 32 Bit Transfer Disabled
Programming Mode Manual
OnBoard FDC Enabled
Serial Port1 3F8H
Serial Port2 2F8H
Parallel Port 378H
Parallel Port Mode Normal
Parallel Port IRQ IRQ5
ECP DMA Channel None
* In order for the hard disk autodetect feature to function, you must first set the Onboard IDE option to Enabled and then reboot the system.
Optimal Defaults Possible Settings
Disabled Enabled, Disabled
4 Sec.* Disabled, 1, 4, 8 and 16 sec.
1 min.* Disabled, 1, 2, 4, 6, 8, 12 and 16 min.
5 min.* Disabled, 5, 10, 15, 20, 30,
40 and 60 min.
Disabled Enabled, Disabled
Disabled Enabled, Disabled
Disabled Disabled,
1, 2, 3, 4, 5, 6, and 7 min.
Disabled Disabled,
5, 10, 15, 30, 45, 60 and 90 sec.
Disabled Disabled, 1, 2 and 4 Rings
Enabled* Enabled, Disabled
Optimal Defaults Possible Settings
Set by BIOS Enabled, Disabled
during boot-up
Disabled Enabled, Disabled
Disabled Enabled, Disabled
Disabled Enabled, Disabled
Auto Manual, Auto
Enabled, Disabled
Set by BIOS Disabled, 3F8H, 2F8H, 3E8H, 2E8H
during boot-up Disabled, 3F8H, 2F8H, 3E8H, 2E8H
Disabled, 278H, 3BCH, 378H
Normal Normal, SPP, EPP, ECP
Set by BIOS None, IRQ5, IRQ7
during boot-up None, CH0, CH1, CH2, CH3
When Enabled, activates power saving modes: DOZE, SLEEP and SUSPEND.
First level of power conservation. The setting defines the timeout period to enter into Doze Mode when no activity is detected.
Second level of power conservation. The setting defines the timeout period to enter into Sleep Mode from Doze Mode.
Third level of power conservation. The setting defines the timeout period to enter into Suspend Mode from Sleep Mode.
When enabled, allows AMIBIOS to monitor every video access as an event.
When enabled, allows AMIBIOS to monitor every bus access from an ISA master device as an event.
Sets a non-activity time-out, after which the hard disk is put into Standby mode. Note that once the hard disk has entered Standby
mode, the next hard disk access will take a few extra seconds to occur.
Sets a non-activity timeout, after which an LCD display is put into Standby mode. Any subsequent detected activity will reenable the
display.
Enables and specifies the number of modem rings required to re-activate the CPU when in Suspend Mode.
When Enabled, warning beeps will be sounded before entering Suspend Mode.
Set to Enabled to use the onboard IDE Controller.
Set to Enabled to activate LBA (Logical Block Address) mode on the IDE Controller's drive. LBA Mode is available only on Enhanced
IDE drives and allows the creation of partition greater than 500MB.
IMPORTANT: To enable LBA mode, ensure that the drives are not partitioned; remove partition before enabling LBA mode (under
DOS, use the FDISK command).
Set to Enabled to allow multiple sector reads and writes with IDE drives (not supported by older IDE drives).
Set to Enabled to allow 32-bit transfers (when supported by the IDE Controller and drives).
When set to Auto, AMIBIOS automatically detects all adapter cards installed in the system and automatically configures the onboard
I/O (serial ports, parallel port, floppy controller, and IDE controller).
All other Peripheral Setup option settings are ignored. Any serial port, parallel port, floppy controller, or IDE controller on an adapter
card in an expansion slot is configured before onboard I/O.
If Auto is selected, AMIBIOS also attempts to avoid IRQ conflicts.
If the offboard serial ports are configured to specific starting I/O ports via jumper settings, AMIBIOS configures the onboard serial ports
to avoid conflicts.
When set to Manual, the settings of the other options in the Peripheral Setup apply. When Manual is chosen, AMIBIOS reports any I/O
conflicts after displaying the BIOS Configuration Summary Screen.
Set to Enabled to use the onboard Floppy Drive Controller.
The setting defines the Serial Port 1 address. If one of these addresses are used by Serial Port 2, it will not be available.
The setting defines the Serial Port 2 address. If one of these addresses are used by Serial Port 1, it will not be available.
The setting defines the Parallel Port address.
Specifies the Parallel Port Mode.
SPP = Standard Parallel Port, EPP = Enhanced Parallel Port, ECP = Extended Capabilities Port.
Specifies the IRQ line to be used for the Parallel Port.
Specifies the DMA channel used for the Parallel Port's ECP mode.
Description
Description
VIPer Software Setups 10-13