Torque - Chrysler 2004 Concorde Service Manual

9 - 18 ENGINE
ENGINE 3.5L (Continued)
DESCRIPTION
Spring Force—Intake
(Valve Open)
Spring Force—Exhaust
(Valve Open)
Number of Coils—Intake
Number of Coils—
Exhaust
Color of Spring (Top of
Coils)
—Intake (Right Hand Coil
Direction)
—Exhaust (Left Hand
Coil Direction)
Wire Diameter—Intake
Wire Diameter—Exhaust
Spring Installed Height
(Spring Seat to Bottom of
Retainer)—Intake &
Exhaust
Oil Pump
Clearance Over Rotors
Cover Out-of-Flat (Max.)
Inner & Outer Rotor
Thickness (MIn.)
Outer Rotor Thickness
(Max.)
Outer Rotor Diameter
(Min.)
Tip Clearance Between
Rotors (Max.)
Oil Pressure
(NOTE: At Normal Operating Temperatures)
Pressure @ Curb Idle
Speed*
Pressure @ 3000 RPM
*CAUTION: If pressure is zero at curb idle, DO NOT
run engine at 3000 RPM.
SPECIFICATION
836–907 N @ 29.85 mm
(188–204 lbs. @ 1.1594
in.)
579–640 N @ 31.47 mm
(130–144 lbs. @ 1.239
in.)
6.86
7.66
Orange
Yellow
4.29–4.34 mm
(0.1689–0.1709 in.)
4.16–4.22 mm
(0.1638–0.1661 in.)
38.0 mm
(1.4961 in.)
0.077 mm
(0.003 in.)
0.025 mm
(0.001 in.)
14.299 mm
(0.563 in.)
0.39 mm
(0.015 in.)
79.997 mm
(3.149 in.)
0.20 mm
(0.008 in.)
34.47 kPa Min.
(5 psi) Min.
300–724 kPa
(45–105 psi)

TORQUE

DESCRIPTION
A/C Compressor Bracket to
Engine—Bolts
A/C Compressor to Bracket
Camshaft Sprocket Bolt—Right
Side
Camshaft Sprocket Bolt—Left Side
Camshaft Thrust Plate—Bolts
Connecting Rod Cap—Nuts
Crankshaft Main Bearing Cap
—Inner Main Cap Bolts
—Outer Main Cap Bolts
—Tie Bolts (Horizontal)
Crankshaft Damper—Bolt
Cylinder Head Bolts*
*Refer to procedure for tightening sequence. (Refer to
9 - ENGINE/CYLINDER HEAD - INSTALLATION)
Cylinder Head Cover—Bolts
Exhaust Manifold to Cylinder
Head—Bolts
Exhaust Manifold Heat Shield—
Bolts
Engine Mount Bracket to
Block—Bolts
Engine Mount Isolator—Nuts
Generator Bracket—Bolts
Intake Manifold
N·m Ft.
Lbs.
54 40
28 —
102 75
+ 1 ⁄ + 1 ⁄
4 4
Turn Turn
115 85
+ ⁄ + ⁄
1 1
4 4
Turn Turn
28 —
54 40
+ 1 ⁄ + 1 ⁄
4 4
Turn Turn
20 15
+ 1 ⁄ + 1 ⁄
4 4
Turn Turn
27 20
+ 1 ⁄ + 1 ⁄
4 4
Turn Turn
28 —
95 70
—Step 1 61 45
—Step 2 88 65
—Step 3 88 65
—Step 4 + ⁄ + ⁄
1 1
4 4
Turn Turn
12 —
23 —
12 —
61 45
61 45
54 40
—M6 Bolts 12 —
—M8 Bolts 28 —
LH
In.
Lbs.
—
250
—
—
250
—
—
—
250
—
—
—
—
—
105
200
105
—
—
—
105
250